763888
5
Verklein
Vergroot
Pagina terug
1/108
Pagina verder
EN
5
each machine function is given in the diagram
(Fig.C) on page 2.
1 = Demolition hammer/chisel
2 = Rotary hammer drill
3 = Drilling

• To start the drill, squeeze the trigger.
• To stop the drill, release the trigger.
Installing dust catcher
Fig. C
The dust catcher prevents large amounts of
drilling dust entering the machine when drilling
into ceilings:
• Remove the drill bit.
• Slide the dust catcher over the shaft of the drill
bit.
• Place the drill bit with catcher in the drill
chuck.
• Always replace a damaged dust catcher
immediately.

Take care that the machine is not
connected to power whenever
maintenance work on the mechanical
parts is taking place.
The machines are designed to function
problem-free for a long period with a minimum
of maintenance. Through regular cleaning and
correct treatment, you help assure a long working
life for your machine.
Defects
The machine should be regularly inspected for
the following possible defects, and repaired if
necessary.
• Damage to power cord
• Broken on/off trigger assembly.
• Short circuiting.
• Damaged moving parts.
Trouble shooting
 

• Failure in power supply.
• Check the power supply.
• Poor contact in the on/off trigger.
• Repair or replace the trigger assembly.
• Mains voltage too low.
• Extension lead too long, or too light.
• Damaged motor.
• Have your machine repaired by an expert.
• Carbon brushes worn.
• Replace the carbon brushes
 

• Motor is overloaded due to excessive
pressure or drilling depth.
• Reduce the pressure or drilling depth,
reduce power.
• Damaged motor.
• Have your machine repaired by an expert.
• Supply voltage too low.
• Adjust the supply voltage.
• Carbon brushes worn.
• Replace the carbon brushes
 
• Overloading of machine, or blunt drill bit
• Reduce the loading, or hone the drill bit.
Replacing carbon brushes
• Regularly check the carbon brushes for wear
and defects.
• Replace both carbon brushes at the same
time.
• Always replace worn-out carbon brushes.
• Always keep the carbon brushes clean, and
make sure that neither brush is obstructed.
• Open the machine to inspect/replace the
carbon brushes.
• Remove and replace the carbon brushes if
necessary.
Cleaning
Clean the machine casings regularly with a soft
cloth, preferably after each use. Make sure that
the ventilation openings are free of dust and
dirt. Remove very persistent dirt using a soft
cloth moistened with soapsuds. Do not use any
solvents such as gasoline, alcohol, ammonia,
etc. Chemicals such as these will damage the
synthetic components.
Lubrication
Fig. A
• Regularly grease the hammer drill shaft.
• Regularly check the grease-level inside the
machine:
• Remove the grease cap (12) on top of the
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm HDM1023 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm HDM1023 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 12,86 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info