763708
5
Verklein
Vergroot
Pagina terug
1/108
Pagina verder
EN
5
Ferm
connected to the terminal which is marked
with the letter N or coloured black.
The wire which is coloured brown must be
connected to the terminal which is marked
with the letter L or coloured red.
Technical data
Mains voltage 230V~
Mains frequency 50Hz
Power input 1,500W
No-load speed 350 - 800 /min
Impact rate 1100 - 2700 /min
Max. drilling diameter
Wood 40 mm
Steel 13 mm
Concrete 36 mm
Weight 6 kg
Noise and vibration
Hammer position
Sound pressure (Lpa) 98.5 dB(A)
Acoustic power (Lwa) 109.5 dB(A)
Uncertainty (K) 3 dB(A)
Vibration main handle 19.819 m/s2
Uncertainty (K) 1.5 m/s2
Hammer/drill position
Sound pressure (Lpa) 96.88 dB(A)
Acoustic power (Lwa) 107.88 dB(A)
Uncertainty (K) 3 dB(A)
Vibration main handle 24.847 m/s2
Uncertainty (K) 1.5 m/s2
Wear hearing protection.
Vibration level
The vibration emission level stated in this
instruction manual has been measured in
accordance with a standardised test given in EN
60745; it may be used to compare one tool with
another and as a preliminary assessment of
exposure to vibration when using the tool for the
applications mentioned
using the tool for different applications, or with
different or poorly maintainted accessories,
may significantly increase the exposure level
the times when the tool is switched off or when
it is running but not actually doing the job, may
signifi cantly reduce the exposure level
Protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
Description
(fig. A)
Your hammer drill has been designed for drilling
holes into wood, steel, and masonry. The machine
can also be used as a demolition hammer in
combination with the SDS chisels.
1. On/off switch
2. Drill selection switch
3. Hammer selection lever
4. Chuck
5. Locking sleeve
6. Main grip
7. Auxiliary grip
8. Depth stop
9. Lubrication point
10. Carbon brush holder
11. Adjusting wheel for electronic speed control
Assembly
Before assembly, always switch off the
machine and remove the mains plug from
the mains.
Mounting and removing the accessory
(fig. B)
Do not use blunt drill bits or chisels.
Immediately sharpen or replace blunt drill
bits or chisels.
Mounting
Apply a few drops of oil to the shaft of the
accessory.
Slide the locking sleeve (5) to the rear.
Insert the accessory into the chuck (4).
Secure the accessory by turning it
counterclockwise until it locks into place.
Release the locking sleeve (5).
Removing
Slide the locking sleeve (5) to the rear.
Remove the accessory from the chuck (4).
Release the locking sleeve (5).
Mounting and removing the auxiliary grip
(fig. C)
Mounting
Loosen the auxiliary grip (7) by turning it
counterclockwise.
Mount the auxiliary grip (7) by sliding it over
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm HDM1022 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm HDM1022 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 1,86 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info