763651
10
Verklein
Vergroot
Pagina terug
1/26
Pagina verder
10
EN
When using the machine sideways
always use the sidewheel
Mounting of the side wheel (Fig. E)
Slide side wheel (13) over the side wheel
holder (14).
Mounting the wire spool (Fig. F1)
Place the spring (17) into the spool housing
(18). Make sure the wider side of the spring is
placed on the trimmer head.
Place the spool reel (16) over the spring (17).
Make sure the wires are passed through the
holes inside the housing (18). (Fig. F2)
Cover the spool reel with the spool cover (15)
and fasten it by turning the cover tightly.
Before replacing the spool clean the
machine from any dirt.
Replacing the spool (Fig. F1)
Remove the spool cover (15)
Take out the spool reel (16) but leave the spring
(17) inside.
Take the new spool reel (GTA1002) and place
it over the spring (17). Make sure the wires are
passed through the holes inside the housing
(18). (Fig. F2)
Cover the new spool reel with the spool cover
(15) and fasten it by turning the cover tightly.
Using the tap and go system (Fig. G)
When the wire is too short, switch the machine
on and press the tip of the spool reel (19) on
the ground (make sure this is done on a hard
surface).
This will release the wire in order to get longer.
The wire will be cut on the correct length
automatically by the blade mounted in the
protection guard (10).
Please keep power switched off and
disconnect the battery.
Tilting the trimmer head (Fig. H)
Press the knob (20) of the trimmer head to tilt
the head in the desired position.
When knob is released, the head will click and
lock in the chosen position
Turning the trimmer head (Fig. I)
Press the ring (21) down towards the trimmer
head to turn the head in the desired position.
When the ring is released, the head will click
and lock in the chosen position
Adjusting the pole height (Fig. J)
To adjust the height of the machine, loosen the
lower adjustment ring (22)
Carefully push the lower shaft (24) from the
upper shaft (23) down or upwards.
Fasten the lower adjustment ring (22) to secure
the height of the machine
Before use, always visually inspect the
machine and its parts are correctly
mounted, not worn out or damaged.
Using your grass trimmer
For your own safety and for best results read
the following user advice and do not use this
product for anything other than its intended
purpose.
This grass trimmer is made for cutting grass.
All other use that is not specifically allowed in
this manual may lead to damage to the grass
trimmer or injury to the user.
Safety features
The protection guard has a knife for cutting
the wire to the correct length. Do not touch the
knife to reduce the chance of injury to the user.
The on/off switch (6) and safety switch (7)
must be operated together to start the motor.
If pressure on one of two switches is released,
the tool is designed to stop rapidly.
Switching On and Off
To switch the trimmer on, press the safety
switch (7) and the start on/off switch (6) at the
same time.
To switch off, release one or both switches.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Ferm-GTM1003

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm GTM1003 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm GTM1003 in de taal/talen: Engels als bijlage per email.

De handleiding is 4,39 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info