110287
7
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
GB
7
Ferm
Special safety instructions
Read the following safety instructions and also the
enclosed safety instructions.
Before using the appliance
Check the following points:
Has the saw blade lost any teeth and is it •
showing cracks or fractures?
If so, replace the saw blade immediately.•
Is there enough room under the workpiece so •
that the saw blade does not come into contact
with the floor or work table as it moves up and
down?
Do the teeth of the saw blade point upwards?•
Always wear protective goggles when using •
the appliance.
Maintain the appliance carefully.•
Do not use the appliance in a wet •
environment.
Do not use the appliance for material which •
contains asbestos.
Never leave the jig saw unattended.•
Using the appliance
Clamp the workpiece that you will be sawing in •
firmly into place.
Remove any wood residue that is near or •
stuck to the surface of the saw blade; do not
use your hand for this. Switch the appliance off
before removing any residue!
Always switch the jig saw on in idle, i.e. switch •
the jig saw on before bringing it into contact
with the workpiece.
When sawing the wood watch out for knots, •
nails, cracks and/or dirt deposits. These can
cause the saw blade to jam dangerously. Also
watch out for this with waste wood. This often
requires less careful sawing, so there is a
danger that you may not be quite so careful
about watching out for irregularities in the
wood.
Do not saw workpieces that are thicker than •
the length of the saw blade.
Do not touch metal parts of the jig saw when •
sawing in walls or floors in which there could
be electricity cables. Hold the jig saw tightly
with both hands on the plastic grip so that you
do not touch parts that could become live if
you accidentally saw through an electricity
cable.
When you have finished sawing, switch off the •
appliance first and wait until the saw blade
comes to a standstill before removing it from
the workpiece.
Keep the plastic guard in place while the jig •
saw is in use.
3. MOUNTING ACCESSORIES
Prior to mounting an accessory always
remove the battery.
Selecting the saw blade
The jig saw is suitable for all commercially
available T-shank saw blades. The profile and the
teeth vary is according to the material that you
want to saw. A fine tooth will give you a smooth
and precise saw cut. Use a narrow profile if you
want to saw curves or if you are going to saw
figures.
The maximum saw capacity in wood is 70 mm.
To select the right saw, proceed as follows:
First of all try a saw blade with coarse teeth.•
If you don‘t get a smooth and precise saw cut, •
try a saw blade with a finer tooth.
For plastic, aluminium and steel always use a •
saw blade with a very fine tooth.
For metal, only use saw blades, suitable for •
metal.
In general you will work faster but less precisely
with a coarse tooth than with a fine tooth.
For an optimum result always make sure the saw
blade is sharp.
Saw blade Type of workpiece
Coarse Wood
Medium Wood
Fine Plastic, aluminium, steel
Very fine Cutting curves (wood)
Assembling saw blade
Fig. B
To assemble the saw, proceed as follows:
Push the saw buckle clamp up and hold.•
Place the saw in the saw buckle. Make sure •
that the teeth point upwards and forward. The
smooth side of the saw must rest against the
wheel.
Push the saw as far into the buckle as •
possible.
Secure the saw by gently releasing the saw •
buckle clamp. Make sure that the saw blade
sits correctly in the saw buckle. A crooked
blade can result in an unsatisfactory cut.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm FPJS 1800 LK bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm FPJS 1800 LK in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 8,08 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info