79265
6
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
6
EN
Replacing cables or plugs
Immediately throw away old cables or plugs when
they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
The tool is suitable for use as a screwdriver
and drill. Any other application is specically
excluded.
3. MOUNTING ACCESSORIES
Inserting and removing bits
Fig. 1
In addition to screwdriver bits with a hexagonal
shaft, this tool can also accommodate drill bits
with a hexagonal shaft.
Always use short screwdriver bits in
combination with the magnetic bit holder.
The 50 mm screwdriver bits can be used
without the magnetic bit holder.
Pull back the locking sleeve (2) and insert the
magnetic bit holder or 50mm screwdriver bit.
Release the locking sleeve.
To remove, pull back the locking sleeve and
remove the bit or magnetic bit holder.
4. OPERATION
Always follow the safety notes and the
relevant safety code.
Hold the appliance rmly and press the
screwdriver steadily onto the work piece. Do not
overload the appliance. Only use bits with no
visible wear. Worn bits will have a bad effect on
the functioning of the appliance.
Adjusting the torque
Fig. 1
The appliance has 17 different torque settings
with which to set the power for driving and
removing screws.
Set the torque settings ring (3) to the desired
position. The available torque settings are
indicated on the settings ring by the numbers 1
to 15 and by dots between the gures to
dene intermediate settings. And a setting for
drilling indicated by the drill icon (17 in total).
You should preferably choose a setting as low
as possible when using the screwdriver. Select
a higher setting if the motor slips.
Driving and removing screws
Fig. 1
Set the direction switch (9) to position ‘ in
order to drive screws.
Set the direction switch (9) to position ‘ in
order to remove screws.
Ensure that the direction switch (9) is
always set to ‘ during drilling and the
drill symbol selected on the torque
settings ring.
Switching the device on and off
Fig. 1
Depress the on/off switch (8). It regulates the
speed of the appliance by transmitting power
to the switch.
Release the on/off switch (8) to halt the drill
chuck immediately, it will no longer run on.
Move the direction reversing switch (9) to the
centre in order to lock the appliance in its
disabled state.
The tool will turn at its slowest speed when the
switch is depressed lightly. The tool will turn at its
fastest speed when the trigger is fully depressed.
Only lay down the appliance when it has stopped
running completely. Do not place it on a dusty
surface as particles of dust could get into the
mechanism.
LED work light
Fig. 2
Press the LED work light switch (11) once to
switch the LED work light on.
Press the LED work light switch (11) again to
switch the LED work light off.
Charging the battery
Only use the battery charger in a temperature
range between + 5 °C to + 40 ºC.
Only use the battery charger in dry, ventilated
rooms.
One advantage of using Lithium-Ion batteries is
that, until the battery is almost empty, hardly any
power fading is noticeable. The machine can be
used until you start noticing that the power of the
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm FDCS 720 L bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm FDCS 720 L in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Deens, Noors als bijlage per email.

De handleiding is 22,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info