510084
5
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
EN
5
Wear a dust mask.
Special safety instructions
• Always keep the cord away from the moving
parts of the machine.
• In the case of locking, switch the machine off
immediately and remove the plug from the
mains.
• Compare the maximum number of revolutions
allowed of the accessories with the number of
revolutions of the machine.
• When you put the machine away the engine
must be switched off and moving parts must
have reached a standstill.
• Never attach an assembly spanner to your
machine with a piece of string or anything
similar.
• Never use the axle locking button if the
machine is operating.
• Make sure that the spring chuck diameter is
the same as the axle diameter of the
accessory.
• Use a clamping device for securing the work
piece.
• Keep your hands away from the work piece.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Your machine is double insulated,
therefore no earthwire is required.
Replacing cables or plugs
If the mains cable becomes damaged, it must
be replaced with a special mains cable available
from the manufacturer or the manufacturer’s
customer service. Dispose of old cables or plugs
immediately after replacing them with new ones. It
is dangerous to connect the plug of a loose cable
to a socket.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1.5 mm
2
. When using a cable
reel always unwind the reel completely.
3. Assembly of accessories
Before assembly always remove the plug
from the mains.
Warning! Change accessories by
inserting an accessory into the collet (or
chuck) as far possible to minimize run out
and unbalance.
Assembly of accessories
Fig. 2
Press down the axle locking button (2) and hold
it down. Using the spring chuck spanner you can
undo the spring chuck (1). Put the accessory in
its place. Hold down the axle locking button when
you fasten the spring chuck with the spring chuck
spanner.
Operation
Switch on the machine by engaging the on/out
switch (A) By adjusting the adjusting wheel (B)
you can regulate the speed of the Combitool. Do
not put the machine down when the motor is still
running. Do not place the machine on a dusty
surface. Dust particles may enter the mechanism.
Too high a load at a low speed of the
Combitool can burn out the engine.
Holding and guiding the tool
Fig. 3
• For precision work (engraving): pencil grip (A)
• For rough work (grinding): paring knife hand
grip (B)
• When you need to keep the tool parallel to the
work surface (e.g. using a cut-off wheel): 2
hand golf grip (C)
4. Accessories for the Combitool
Ferm does not deliver spare accessories for the
Combitool. The Combitool is designed to use
the standard accessories of Dremel, Black &
Decker, Bosch or Proxxon. Always check that the
maximum rpm of the accessory is suitable for the
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm CTM1012 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm CTM1012 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 2,65 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info