632670
5
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
5
EN

Fig. 1
1. Bit holder
2. On/Off-switch
3. Softgrip
4. LED (Red)
5. Charger connection
6. Extension piece
7. Bit
8. LED (White)
2. SAFETY INSTRUCTIONS

DESCRIPTION (FIG. A)
Denotes risk of personal injury, loss of
life or damage to the tool in case of
non-observance of the instructions in
this manual.
Indicates electrical shock hazard.
Indoor use only
In case of failure, the transformer is not
dangerous
Thermic protector
Do not dispose of in household waste.

Only use the accumulator block with the
battery charger provided – using other
chargers could be dangerous.
Keep the accumulator block, tool and battery
charger away from damp and wet conditions.
Before using the battery charger, check all
wires are properly connected.
If any wires on the charger are damaged, do
not use it until these have been replaced.
When the charger is not in use it should not be
plugged in.
When unplugging, do not pull the plug out by
the cable.
If the charger breaks down or suffers from
other technical problems, take it to a
recognised dealership to be checked before
using it again. Any damaged parts must be
replaced.
Take care when handling the accumulator
block, do not drop it or knock it against other
things.
Never attempt to repair the battery charger or
accumulator block yourself; this can be
extremely dan gerous. Repairs should always
be carried out by a recognised dealership.
Always unplug the charger before cleaning or
carrying out any other maintenance on it.
Do not attempt to charge the accumulator
block in temperatures of below 5 degrees or
above 40 degrees centigrade.
Never throw the accumulator block into water
or a re – it may explode.
Turn the drill immediately off after the screw is
fasten ed. Overloading and damaging the
battery or motor can be prevented this way.
Use the torque to loosen the fastened screw

When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of re, electric shock and personal
injury.
Read the following safety instructions and also
the enclosed safety instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Class ll machine. Your machine is
double insulated; therefore no earthwire
is required.
Replacing cables or plugs
Immediately throw away old cables or plugs when
they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.


Fig. 1 + 7
The bits can easily be placed directly into the bit
holder or on the extension piece. The extension
piece can be used for screws that are difcult to
reach.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm CDM1106 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm CDM1106 in de taal/talen: Nederlands, Duits, Engels, Frans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 9,48 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info