632671
4
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
GB
4 Ferm
3. MOUNTING ACCESSORIES
Prior to mounting an accessory always
remove the battery.
Connecting and removing the battery
Fig. 1 + 2
Ensure that the direction reversing switch (6) •
is in the central position in order to prevent the
appliance from being switched on
unexpectedly.
Insert the battery into the base of the •
appliance, as shown on the illustration. Push
the battery until it latches in.
Press the locking button (4) on either side •
before removing the battery, and disengage
the battery from the base of the appliance.
Only use batteries of the following type. Using any
other batteries could cause serious injury or
damage the tool.
CDA1051: FPB-1800L, 18V Lithium-Ion
CDA1053: FPB-1800N, 18V NiMH
The following charger can be used to charge these
batteries.
CDA1052: FPL-1800 (Lithium-Ion and NiMH)
CDA1054: FPL-1800N (NiMH only)
4. OPERATION
Operation
The impact wrench is driven by an electric motor
via a gear and impact mechanism.
The impact mechanism starts when the screwed
connection runs tight and load is put on the motor.
The mechanism converts the power of the motor
to steady rotary impacts.
Always observe the safety instructions
and applicable regulations.
Fig. 1
Firmly hold the machine and push the bit with even
pressure into the workpiece. Do not force the
machine.
Use only bits that do not yet show any signs of
wear. Worn bits have a negative effect on the
efficiency of the machine.
Screwing screws in and out
• Setthedirectionswitch(6)onposition‘4 for
putting in screws.
• Setthedirectionswitchonposition3 for
removing screws.
Be sure that the direction switch (6)
always in position 4’ during drilling.
Regular check the chuck for possible
damage.
Possible use a coolant. In case of
drilling in walls, watch out for drilling in
electric wires of water pipes. Get advice
according to the use from your dealer.
Switching on and off
Fig. 1
• Presstheon/offswitch(7)in.Youregulatethe
speed of the machine by the degree to which
you keep the switch pressed in.
• Releasingtheon/offswitch(7)causesthedrill
to stop immediately
• Slidethedirectionswitch(6)tothemiddleto
lock the machine in switched off mode.
Do not put the machine away until the machine
has completely stopped running. Do not store the
machine on a dusty surface. Dust particles can get
into the mechanism.
Only operate the drill with the forward /
reverse switch (7) fully engaged. Never
attend to use the drill with this switch in
the neutral position.
5. SERVICE & MAINTENANCE
Make sure that the machine is not live
when carrying out maintenance work on
the motor.
The machines have been designed to operate
over a long period of time with a minimum of
maintenance. Continuous satisfactory operation
depends upon proper machine care and regular
cleaning.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm CDM1087 - FPDW-1800 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm CDM1087 - FPDW-1800 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 7,74 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info