762277
5
Verklein
Vergroot
Pagina terug
1/84
Pagina verder
then you can continue charging, and if so, then
charging is finished. You should then set the
“Voltage” switch to “Off”. Then remove the
mains power plug and the two clips from the
plus and minus terminals of the accumulator.
(When charging the battery while still in the
vehicle, you should first remove the clip
connected to the chassis.)
4. OPERATING THE BATTERY
CHARGER
The integral flat fuse protects the equipment from
polarity reversal and short circuits. If the fuse
suffers a defect it must be replaced by a new fuse
with the same amp value. If you wish to replace the
flat fuse, first pull the mains plug out of the socket
and remove the charger clamps from the battery.
In the event of a thermal overload, an automatic
circuit breaker will stop the charging process. After
a cooling break it will cut in again automatically.
Explanation of switches, indication lights and
display on front panel
6V / 12V
The battery charger can charge batteries of 6V
and 12V. For this purpose push the switch at the
right side of the front panel in chosen position.
Charging process
Connect the clamps correctly to the battery
and connect the plug to the mains.
Select the voltage 6V / 12V switch
The charging current is now visible on the
display on the front. This current meter is not
a precision instrument and only gives a rough
indication of the charging current.
Disconnect from the mains supply.
Remove the clamps from the + and - poles of
the battery.
Trouble shooting
1. No charging current
Bad contact of power socket
Contact qualified electrician
Select Voltage 6V / 12V is set incorrectly
Select correct voltage position
Initial voltage is too low
Change battery
+ and - poles of battery are oxidized and/or
dirty
Clean poles
Battery has been damaged
Replace the battery
2. Low charging current
+ and - poles of battery are oxidized and/or
dirty
Clean poles
Battery is charged fully
Measure specific gravity
3. Excessive transformer noise
Select Voltage 6V / 12V is set incorrectly
Select correct voltage position
Unstable position
Change position for proper placement
Check charged battery
On the basis of the specific gravity of the battery
acid can be gathered if an battery is fully loaded
or not. With the help of a specific gravitymeter the
specific gravity can be appointed.
Empty battery: s.g. = 1.13 kg/ dm³
Full battery : s.g. = 1.28 kg/ dm³
CAUTION! The gas mixture is explosive.
You must remove the power plug from
the mains socket before connecting or
disconnecting the battery.
5. MAINTENANCE
Always remove the plug from the mains socket
when the battery charger is being serviced or
cleaned. Never use any water or other liquids
when cleaning the charger. Keep the cable
and your battery charger clean. Some cleaners
and solvents (petrol, thinner) can affect or
dissolve plastic parts. These products contain
a.o. benzene, trichloroethylene, chloride and
ammonia.
CAUTION! To avoid electrical danger, the
charger should be connected to a mains
supply with good earthing and may not be
subjected to rain or snow. Any damaged
cables must be immediately replaced by
a qualified specialist.
5
EN
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm BCM1021 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm BCM1021 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 7,53 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info