763617
6
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
GB
6Ferm
Fasten the side handle for left-hand operation •
on the right-hand side of the machine.
Fasten the side handle for right-hand operation •
on the left-hand side of the machine.
Make sure that the side handle is
fastened properly and cannot loosen
unexpectedly.
Mounting the guard
Fig. 2
Mount the guard before using the machine.
Assembly
Place the guard (2) on the housing. Be aware •
that the notch of the guard falls across the edge
of the housing.
Place the fixing-ring (7+12) on the guard: the •
ring-holes have to be on the screw-holes.
Mount the guard en fixing-ring with help of the •
4 screws and washers (8).
The closed side of the guard always has to •
point in the user’s direction.
Be aware the screws are tightened well
enough. Check regularly if the screws
are still fixed.
Disassembly
Remove the flange nut and the grinding disc •
with lower flange from the spindle.
Unscrew the 4 screws (with washers) en •
remove the fixing-ring.
Remove the guard from the machine.•
•
Mounting a grinding disc
Fig. 3
Use grinding discs of the correct dimension. Use
fibre reinforced grinding discs only. The grinding
disc must not touch the edge of the guard.
Remove the plug from the mains
Press the spindle lock (Fig. 1 - 5) and turn the •
spindle (6) until it engages in the lock. Keep the
spindle lock pressed during this procedure.
Remove the flange nut (10) from the spindle •
using the spanner (11).
Position the grinding disc on the flange (9).•
Place the flange nut on the spindle and tighten •
it using the spanner.
Release the spindle lock and check that the •
spindle is unlocked by rotating it.
Mounting grinding discs and roughing discs
Fig. 4 and 5 show how to mount the flange (10)
when using thick (4 – 8 mm) and thin (2,5 – 4 mm)
discs.
4. USE
Always observe the safety instructions
and applicable regulations.
Special attention when starting the machine
Clamp the workpiece and make sure that the •
workpiece cannot slide from under the machine
during the cutting activities.
When working with the machine, always hold it •
firmly with both hands and provide for a secure
stance.
Always direct the cable to the rear away from •
the machine.
Insert the mains plug only when the machine is •
switched off.
Apply the machine to the workpiece only when •
switched on
Never use the machine for grinding
magnesium workpieces.
Switching on and off
Slide the on/off switch forwards.•
To switch off, depress the on/off switch, this will •
then jump to the ‘off’ position.
Do not put the machine down when the
motor is still running. Do not place the
machine on a dusty surface. Dust
particles may enter the mechanism.
Operation
Hold the machine firmly and move it against the •
workpiece. Move the grinding disc evenly
across the workpiece.
Move the machine during roughing under an •
angle of 30º - 40º across the workpiece (Fig. 6).
Never use grinding discs for roughing!
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm AGM1027 - FDAG-750 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm AGM1027 - FDAG-750 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 11,02 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info