443094
7
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
PRINCETON CHORUS DSP - REAR PANEL
FCC COMPLIANCE NOTICE
A PRODUCT OF:
PRINCETON CHORUS DSP
A. IEC LINE CORD CONNECTOR - The line cord
must be connected to a grounded AC recepta-
cle in accordance with the voltage and frequen-
cy ratings as shown on the rear panel of the
amplifier ( {B}INPUT POWER ).
C. FOOTSWITCH - Plug-in connection for the
FOOTSWITCH (P/N 0055592000) for remote
switching of the Overdrive Mode, and both
DSP Effects circuits. NOTE: For proper opera-
tion of the FOOTSWITCH, the DRIVE SELECT
switch and both DSP Effects DEFEAT switches
on the front panel must all be OUT. (A speaker
grade cord is preferable to a coax guitar cord
for connecting the FOOTSWITCH.)
D. EFFECTS LOOP STEREO SEND - This jack
provides a line-level stereo output from the pre-
amp and both DSP Effects circuits of the
Princeton Chorus DSP. This output can be used
in conjunction with the {E}STEREO RETURN as
a patch point for external stereo effects devices.
(See “EFFECTS LOOPS - CONNECTION DIA-
GRAMS,” page 8) The EFFECTS LOOPS-
STEREO jacks are standard 1/4-inch
Tip-Ring-Sleeve types, with:
•Left channel signal on the Tip
•Right channel signal on the Ring
This send can also be used to feed a stereo sig-
nal to two channels of a recording or sound
reinforcement mixer. Additionally this output
can be used to drive another Princeton Chorus
DSP as a slave amplifier. This is done by con-
necting a shielded stereo cord from the
{D}STEREO SEND jack of the master ampli-
fier to the {E}STEREO RETURN jack of the
slave amplifier.
E. EFFECTS LOOP STEREO RETURN - This
stereo jack inputs signal directly to the left and
right power-amps. It automatically disconnects
the pre-amp and DSP Effects circuits when
used. This is useful when using the Stereo
E ffects Loop option, or when using the
Princeton Chorus DSP as a slave amplifier for a
stereo signal source.
F. EFFECTS LOOP MONO SEND - This jack pro-
vides an impedance-balanced mono output sig-
nal from the pre-amp at a point before the DSP
Effects circuits. This output can be used in con-
junction with the {G}MONO RETURN as a
patch point for external mono effects devices.
(See “EFFECTS LOOPS - CONNECTION DIA-
GRAMS,” page 8) The {F}MONO SEND can
also be used to send recording and sound rein-
forcement mixers a dry signal. Additionally this
output can be used to drive another Princeton
Chorus DSP as a slave amplifier. This is done
by connecting a standard guitar cord from the
{F}MONO SEND jack of the master amplifier to
the {G}MONO RETURN jack of the slave amplifier.
G. EFFECT LOOP MONO RETURN - This bal-
anced jack inputs signal to the stereo DSP
Effects circuitry, which drives the stereo power-
amp section. It automatically disconnects the
pre-amp signal when used. This is useful when
using the Mono Effects Loop option or when
using the Princeton Chorus DSP as a slave
amplifier for a mono signal source. The DSP
Effects are active in the slave amplifier so that a
true stereo image will be generated if the DSP
Effects are used. NOTE: In order to function
properly, a dummy plug or an extra guitar cord
must be inserted into INPUT 2 on the front
panel of the slave amplifier with its VOLUME
controls turned down.
7
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide a re a-
sonable protection against harmful interf e r ence in a re s i d e n-
tial installation. This equipment generates, uses and can
radiate radio frequency energy and if not installed and used
in accordance with the instructions, may cause harm f u l
i n t e rf e r ence to radio communications. However, there is no
guarantee that interf e rence will not occur in a part i c u l a r
installation. If this equipment does cause harmful interf e r-
ence to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is
encouraged to try to correct the interf e rence by one or more
of the following measures: •Reorient or relocate the re c e i v-
ing antenna •Increase the separation between the equip-
ment and receiver •Connect the equipment into an outlet on
a circuit diff e rent from that of the receiver Consult the deal-
er or an experienced radio/TV technician for help
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Fender Princeton Sterio Chorus DSP bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Fender Princeton Sterio Chorus DSP in de taal/talen: Engels als bijlage per email.

De handleiding is 1,81 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info