443017
7
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
7
Rear Panel
Trans-Impedance Power Attenuator
K. OVERDRIVE ONOFFPress IN to engage the Overdrive
circuit as indicated by the LED. See FOOTSWITCH {Z}.
OVERDRIVE Off OVERDRIVE On
L. OVERDRIVEAdjusts the amount of signal distortion
provided by the Overdrive effect.
M. TONEAdjusts the Overdrive tone characteristics.
N. LEVELAdjusts the Overdrive volume output, useful for
boosting gain to generate additional tube distortion.
O. TRANSIMPEDANCE POWER ATTENUATORWhen
set to FULL VOLUME, the attenuator circuit is bypassed
allowing the maximum output from the tube ampli-
fier. When set to SILENT, the speaker is disabled, but
HEADPHONE and LINE OUT outputs may be used. At
any setting beside FULL VOLUME (including SILENT) the
power attenuation circuit controls the output loudness
of the speaker, while preserving the tube amp + speaker
“feel” and dynamics achieved through amplifier volume
and playing intensity.
(US PATENT # 6,816,009)
P. FUSE
Protects the amplifier from electrical faults. Only
replace a blown fuse with the type and rating specified
on the rear panel of your amplifier.
Q. IEC POWER INPUT SOCKETConnect to a grounded
outlet using the supplied power cord in accordance with
the voltage and frequency ratings specified on the rear
panel of your amplifier.
R. POWERTurns the Princeton Recording-Amp ON-OFF.
S. SPEAKER OUTPUTConnection for the speaker.
CAUTION: An Ω speaker must ALWAYS be connected when
the amplifier is ON or damage may occur.
T. HEADPHONE / A speaker-emulated
output for use with standard Stereo or Mono head-
phones. Accepts a standard /" plug.
U. LINE OUTA studio-quality, speaker emulated, balanced
XLR output suitable for recording or sound reinforcement
applications.
V. LINE LEVEL
Adjusts the output level of the LINE OUT
{U} jack. Use to accommodate the input sensitivity of
your connected equipment.
W. GROUND LIFT Press IN to disconnect the LINE
OUT {U} ground pin () to reduce noise caused by non-
standard wiring. Leave OUT for normal operation.
X/Y
. SEND / RECEIVEEffects loop jacks. Connect SEND {X}
to your effects input and RETURN {Y} to effects output.
Set your effects device level control (if any) as close to
dBu as possible.
Z. FOOTSWITCHConnect the included -but-
ton footswitch using the supplied -pin DIN cable to
enable remote on-off switching of: OVERDRIVE {K},
COMPRESSOR {H}, FX LOOP {X,Y} and REVERB {F}.
NOTE: The footswitch buttons override the corresponding
panel controls.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Fender Princeton Recording-Amp bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Fender Princeton Recording-Amp in de taal/talen: Engels als bijlage per email.

De handleiding is 16,54 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info