502499
3
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
3
TECHNICAL DATA
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept close at hand to
use when carrying out maintenance on the indicated parts.
If the tool is used with care and normal maintenance is carried
out, it will work well for a long time.
The functions and use of the tool you have bought shall be
only those described in this manual. Any other use of the
tool is strictly forbidden.
PLANER SAFETY RULES
Planer Safety Rules
- Wait for the cutter to stop before setting the tool down. An
exposed cutter may engage the surface leading to possible
loss of control and serious injury.
- Do not reach into the saw dust ejector with your hands.
They could be injured by rotating parts.
- Apply the machine to the workpiece only when switched on.
Otherwise there is danger of kickback when the cutting tool
jams in the workpiece.
- When working, always hold the planer in such a manner that
the planer base plate faces at on the workpiece. Otherwise
the planer can become wedged and lead to injuries.
- Never plane over metal objects, nails or screws. The planer
blade and the blade shaft can become damaged and lead to
increased vibrations.
- Secure the workpiece. A workpiece clamped with clamping
devices or in a vice is held more secure than by hand.
- Never use the machine with a damaged cable.
Do not touch the damaged cable and pull the mains plug
when the cable is damaged while working. Damaged cables
increase the risk of an electric shock.
Products sold in GB only: Your product is tted with an BS
1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug tted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or less.
ILLUSTRATIONS
DESCRIPTION (See gures)
A Safety push button switch (Fig. 1)
B On-/off switch (Fig. 1)
D Support foot (Fig. 2)
E Drive wheel (Fig. 4)
F Toothed belt (Fig. 4)
G Idler pulley (Fig. 4)
H Vertical depth graduated scale (Fig. 2)
I Side end-stop immobilisation control (Fig. 1)
J Circular depth graduation scale (Fig. 1 and 2)
K Depth graduation handle (Fig. 2)
L Lateral stop (Fig. 1)
M Sawdust extraction (Fig. 2)
N Cope depth end-stop (Fig.2)
O Blade replacement screws (Fig. 3)
P Guide slot (Fig. 1)
Q Toothed belt cover (Fig. 4)
R Toothed belt cover screw (Fig. 4)
S Mobile plate (Fig. 2 and 3)
T Dust suction adapter (Fig. 1)
U Base plate (Fig. 1 and 3)
V Side stop locking set square (Fig.1)
W Side stop regulation of the wing nut (Fig. 1)
Y Depth stop xing wing nut (Fig. 2)
EQUIPMENT
- Dust suction adapter
- Hexagonal key
- Lateral stop
- Depth end-stop
- Operating instructions
- Safety instructions
- Warranty
BRIEF DESCRIPTION
This tool has been designed to rout wood and similar
materials, to plane irregular surfaces and to cant off edges.
BEFORE USING THIS TOOL
Before using the tool, make sure the mains voltage is correct:
it must be the same as that on the specication label.
Machines with 230V can also be connected to a 220-V mains
supply.
START UP
WARNING! Only plug in when machine is switched off.
Press the locking button A, and squeeze the trigger in the on/
off switch B. When the on/off switch is released, the machine
stops.
For safety reasons, it is not possible to lock On/Off switch
B, instead it has to be pressed while the machine is being
used.
CONSTANT ELECTRONICS (Mod. PF102/1100VES)
The built-in module permits:
- Soft start.
- The maintenance of a practically constant rated speed
up to rated power.
- An overload protection system by means of current
cut-off in the case of motor overload, in which case the
burring machine shuts down and re-starts when the grinding
pressure has been reduced.
Planes PF82/710 PF102/1100VES
Absorbed power W 650 1100
No-load speed /min 14000 11000
Cutting depth mm 0-2 0-2,5
Total cut width mm 82 102
Rebate’s depth mm 15 15
Approx. weight (without accessories) Kg 3,5 3,8
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Felisatti PF82 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Felisatti PF82 in de taal/talen: Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 1,76 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info