706565

Faber Opti-myst 3 step Handleiding

13
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE ATTEMPTING ANY
MAINTENANCE
Fitting Replacement lamps.
If a large amount of the smoke appears grey or colourless it may be that one or more lamps have
failed.
You can check for lamp failure as follows.
1. Leaving the  ame e ect on, gently pull the drawer fully out by the tab. (See Fig. 3)
2. View the lamps from a distance in front of the  re and observe which lamp needs to be changed.
3. Put Switch ‘A’ in the ‘OFF’ position, and unplug the  re from the mains.
4. Leave the appliance for 20 minutes to allow the lamps to cool down before removing them.
5. Remove the water tank by lifting upwards and place in a sink.
6. Remove the sump as described in the Cleaning Section.
7. Remove the defective lamp, by gently lifting vertically and disengaging the pins from the lamp
holder, (See Fig. 4 and 5). Replace with a Dimplex Opti-myst, 12V, 50W, Gu5.3 base, 8° beam
angle, coloured lamp. (Purchased from www.dimplex.co.uk under the section ‘After Sales Service’,
details of how to purchase the lamps are contained therein.)
8. Carefully insert the two pins of the new lamp into the two holes in the lamp holder. Push  rmly in
place. (See Fig. 4 and 5).
9. Replace the Sump and water tank and carefully close the drawer.
10. Switch on.
Filling the water tank.
When the water tank is empty,  ame and smoke e ect shuts o , and you will hear 2 audible ‘beeps’.
Follow these steps to re ll:
1. Press Switch ‘A’ to (0) (See Fig. 2)
2. Gently pull out the drawer as far as possible by the tab. (See Fig. 3)
3. Remove the water tank by lifting upwards and outwards.
4. Place the water tank in sink and remove cap, Anti-clockwise to open. (See Fig. 6)
5. Fill tank with ltered tap water only. This is necessary to prolong the life of the  ame and smoke
producing unit.
The water should be  ltered through a conventional domestic water  lter unit and the  lter
should be replaced regularly.
6. Screw the cap back on, do not overtighten.
7. Return the tank to the sump, with the tank cap facing down and the  at side of the tank facing
outward.
8. Gently push the drawer back in as far as it will go.
9. Press Switch ‘A’ to ‘ON’ ( I ) position (See Fig. 2)
10. Press Switch ‘B’ once to turn on  ame e ect. (See manual control section and Fig. 2)
Cleaning.
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE HEATER.
We Recommend cleaning the following components once every 2 weeks, particularly in hard water
areas:-
Water Tank, Sump and Seal, Sump lid, Tank cap and seal, Air  lter.
For general cleaning use a soft clean duster – never use abrasive cleaners. To remove any accumulation
of dust or  u the soft brush attachment of a vacuum cleaner should occasionally be used to clean the
outlet grille of the fan heater.
Water tank
1. Remove water tank, as described earlier, put into sink and empty water.
2. Using the supplied brush gently rub the inside surfaces of the cap paying particular attention to
the rubber ring in the outer groove and the centre rubber seal.
3. Put a small quantity of washing up liquid into the tank, re t the cap and shake well, rinse out
until all traces of washing up liquid are gone.
4. Re ll with  ltered tap water only, replace the cap, do not overtighten.
Sump
1. Press Switch ‘A’ to the ‘OFF’ (0) position
2. Gently pull the drawer out as far as possible. (See Fig. 3)
3. Remove the water tank by lifting upwards.
4. Disconnect the electrical connector, located on the left side of the sump, by  rst loosening the
two retaining screws and gently withdrawing the connector. (See Fig. 8)
5. Release the lower sump locking tabs by turning 90°, this allows the sump to be lifted completely
from its location. (See Fig. 9)
6. Gently lift up the sump assembly, taking care to keep level so as not to spill any water. Sit the
assembly in the sink. (See Fig. 10)
7. Release the two upper sump locking tabs by turning 90°, then lift o the sump lid. (See Fig. 11)
8. Carefully tilt, as shown, so that the liquid drains out of the sump. (See Fig. 12)
9. Put a small amount of washing up liquid into the sump, and using the supplied brush, gently
clean all surfaces including the metal disc and the rubber seal located in the top grooved surface.
Do not remove the rubber seals. (See Fig. 13 and 14)
10. When cleaned, thoroughly rinse the sump with clean water.
11. Clean the outlet surface of the sump lid with the brush and  ush out thoroughly with water. (See
Fig. 15 & 16)
12. Reverse the above steps to reassemble.
Air  lter.
1. Press Switch ‘A’ to the ‘OFF’ (0) position (See Fig. 2)
2. Gently pull the drawer out as far as possible. (See Fig. 3)
3. Remove the tank and place in a sink with the cap facing upwards.
4. Gently slide upwards the air  lter plastic holder. (See Fig. 17)
5. Remove the  lter combination from the plastic holder.
6. Gently rinse with water in the sink and dry with fabric towel before returning.
7. Replace the  lter combination making sure that the course black  lter is in contact with the
plastic holder. (See Fig. 18)
8. Replace the tank.
9. Close the drawer fully.
10. Press Switch ‘A’ to the ‘ON’ ( I ) position (See Fig. 2)
Recycling.
For electrical products sold within the European Community. At the end of the electrical
products useful life it should not be disposed of with household waste. Please recycle
where facilities exist. Check with your Local Authority or retailer for recycling advice in your
country.
After Sales Service.
Your product is guaranteed for one year from the date of purchase. Within this period, we undertake
to repair or exchange this product free of charge (excluding lamps & subject to availability) provided
it has been installed and operated in accordance with these instructions. Should you require after
sales service or should you need to purchase any spares, please contact the retailer from whom the
appliance was purchased or contact the service number relevant to your country on the warranty card.
Please do not return a faulty product to us in the  rst instance as this may result in the loss or damage
and delay in providing you with a satisfactory service.
Please retain your receipt as proof of purchase.
Symptom Cause Corrective Action
The  ame e ect will not start. Mains plug is not plugged in.
Switch A is in the ‘ON’ ( I ) position, but mode Switch B has not been pressed.
(See Fig. 2)
Low water level.
Low voltage connector not connected properly. (See Fig. 8)
Check plug is connected to wall socket correctly.
Press Switch B once for  ame e ect. (See Fig. 2)
Check the water tank is full and there is water in the sump.
Check that the connector is inserted correctly. (See Fig. 8)
The  ame e ect is too low. Flame e ect thumb wheel is set too low.
(See Fig. 2)
The water in the sump may be too high due to the drawer being opened and
closed a number of times, water tank removed a number of times, or the  re
has been moved.
Metal Disc at the base of Sump might be dirty (See Fig. 13)
Increase level of  ame by turning thumb wheel D clockwise slowly. (See Fig. 2)
If water level in the sump is more than 40mm, the sump should be removed and
emptied in the sink.
Clean Metal Disc with soft brush supplied. (See Fig. 13) See ‘Maintenance.’ for a
step by step procedure.
Unpleasant smell when unit is used. Dirty or stale water.
Using un ltered tap water.
Clean the unit as described under maintenance.
Use only  ltered tap water.
The  ame e ect has too much smoke. Flame e ect setting is too high. Turn the  ame e ect Thumb Wheel D down to minimum and slowly turn up,
about ¼ a turn, at a time. Give the  ame generator some time to adjust before
increasing. (See Fig. 2)
Main lamps are not working and there
are no  ames or smoke.
There is no water in the tank. Follow instructions under Maintenance, ‘Filling the water tank’.
Check the plug is connected to wall socket correctly.
Switch ‘A’ Fig. 2 is in the ‘ON’ ( I ) position.
Press switch ‘B’ Fig. 2 until you can hear one beep only, for  ame e ect.
Troubleshooting
8
… 13 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Faber Opti-myst 3 step bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Faber Opti-myst 3 step in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 2,86 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info