605063
22
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
CV Explanation Presetting. Value range
7 Software-Version 2-
8 Manufacturercode 85 -
47 Adresse HighByte 0 0-255
48 Adresse LowByte Adresse = CV47*256 + CV48 1 1-255
49 Configuration: 0 0-255
Bit 7 0=DCC 1=Mot
50 Speed of merry-go-round 60 0-255
51 Speed to go to limit switch 15 0-255
54 Speed for drive to zero 40 0-255
55 Time lag on starting in 1 ms steps 250 0-255
56 Time lag on braking in 1 ms steps 105 0-255
57 Running time of merry-go-round 102 0-255
98 Pause in 0.5 s steps 0 0-255
The data format for digital operation and digital operation mode is saved in the CV49.
To CV49:
DCC: Operation modes: with automatic CV49=0
without automatic CV49=1
Motorola: Operation modes: with automatic CV49=128
without automatic CV49=129
Note to CV49:
Do not use any other values! If the CV49 was programmed to 128 or 129,
the controls now only react to the Motorola data format and can only be put back
in DCC mode by means of key programming.
General note:
All CVs are only programmable with a DCC digital centre at the programming track output.
Note re. CV8:
If any random value is programmed in the CV8, all CVs will be reset back to the factory setting.
Operation:
Digital operation:
-------------------------------
Digital mode 1: (CV49-Bit0=0)
The start can be performed via the coil item address after that address has been given the status »green«.
All operating sequences will then be those of a start triggered using the start button.
Sound outputs:
Sound output 1 is activated for 0.5 s as soon as the merry-go-round is started.
Sound output 2 is activated at the end of the running time.
Key programming:
---------------------------------
The programming key cannot be used unless the attraction is at rest
(swing in its lowest position, reed sensor closed)!
1) Press the key -> the LED flashes 3 x
2) Now actuate some points on a Motorola control unit: the LED flashes 3 x and the address
has been adopted. The control unit displays the Motorola data format.
If a DCC capable control unit is used:
3) Press the key again -> the LED flashes 3 x
4) Now actuate some points on a DCC capable control unit: the LED flashes 3 x and the address has been
adopted. The control unit displays the DCC data format.
If no entry has to be made:
5) Press the key again -> the LED flashes 3 x. The control unit is in the working mode again.
Important:
-------------------
If key programming was used to set the control unit to Motorola data format, it cannot be read and
programmed via a DCC capable programming track.
If the control unit has to be set back again from Motorola data format to DCC data format,
it must first be set to the DCC mode through key programming.
Protection of motor power stage and stop outputs:
-------------------------------------------------------------------------------------------
The LED flashes rapidly -> Short-circuit at motor output.
The power stage switches off and the processor performs a reset after a few seconds.
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw FALLER 140424 Fahrgeschaft Crazy Clown bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van FALLER 140424 Fahrgeschaft Crazy Clown in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 4,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info