626606
2
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
2
2 3
DESCRIPTION ÉTIQUETTE ( Figure 2 )
A - Code d’identification du modèle
B –
Numéro d’identification du lot de production
C – Lire les instructions
D – Éliminer selon les directives en vigueur
E - Référence organisme notifié (notified body)
Fréquence de fonctionnement
868.92 MHz ±100KHz
Type batterie 2 piles 3 V au lithium
CR2032
Usage exclusif
Ouvre-portail
Ce produit est conforme à la directive
99/05/CEE
TO RECOGNISE A MASTER/SLAVE TX
•master : if you press any key of a master TX, the LED
flashes before becoming steady.
•slave : if you press any key of a slave TX, the LED
goes on immediately with steady light.
PROGRAMMING SEQUENCE
1)Power up the system after installing and connecting
the electrical components of the 868 SLH System.
2)Use a master TX to set the “site code” on the deco-
ding card/RP receiver (see “system coding”).
3)Use the same master TX to set the site code” on
the system’s other TXs (See “TX coding”).
4)Coded TXs are automatically stored in the de-
coding card/RP receiver by simply activating the
transmitter channel twice in succession within 5
seconds.
SYSTEM CODING
•Simultaneously press push-buttons P1 and P2 of the
master TX and release them when the LED flashes
(after about one second);
•Press and hold down the learning button on the
decoding card/RP receiver: the LED must flash;
•While the master transmitter’s LED is flashing, press
and hold down a channel (the TX’s LED goes on with
steady light);
•Before releasing the learning button on the deco-
ding card/RP receiver, check if the LED goes on with
steady light for a couple of seconds to confirm that
the “site code” was saved.
•Release the button of the master TX channel.
TX CODING
•Simultaneously press push-buttons P1 and P2 of
the master TX used for coding the system and re-
lease them when the LED flashes (after about one
second);
•Frontally bring into contact the master TX and the
TX to be coded (master or slave) ;
•On the master TX (while its LED is flashing), press and
hold down the same channel used for coding the
system: the LED goes on with steady light;
•Press the required channel on the TX to be coded
and release it when the LED goes off after flashing
twice to confirm the “site code” was saved;
•Release the button of the master TX channel;
•Repeat this procedure for every TX to be coded.
COMMENT RECONNAÎTRE UN TX MAÎTRE/ESCLAVE.
•maître : en appuyant sur une touche quelconque
d’un TX maître, la Led clignote avant de s’allumer
avec une lumière fixe.
•esclave : en appuyant sur une touche quelconque
d’un TX esclave, la Led s’allume immédiatement
avec une lumière fixe.
SEQUENCE DE PROGRAMMATION.
1)Alimenter l’installation après avoir effectué l’instal-
lation et les connexions électriques des composants
du Système 868 SLH.
2)Utiliser un Tx maître pour fixer le “code installation”
sur la carte de décodage/ récepteur RP (voir “co-
dage installation”).
3)Utiliser le même Tx maître pour introduire le code
installation sur les autres Tx de l’installation (voir “co-
dage Tx”).
4)Les Tx codifiés seront mémorisés automatiquement
dans la carte de décodage/récepteur RP en activant
simplement deux fois de suite, dans un délai maxi.
de 5 secondes, le canal de l’émetteur.
CODAGE INSTALLATION.
•Appuyer simultanément sur les poussoirs P1 et P2
du Tx maître et les relâcher lorsque la Led clignote
(au bout d’une seconde environ);
•Sur la carte de décodage/récepteur RP, appuyer
et maintenir dans cette position le poussoir d’auto-
apprentissage: la Led doit clignoter;
•Sur le Tx maître (tandis que la Led
clignote) appuyer et maintenir dans cette
position un canal (la Led de l’émetteur s’allume avec
une lumière fixe);
•Sur la carte de décodage/récepteur RP, vérifier l’al-
lumage fixe de la Led pendant deux secondes, pour
avoir la confirmation que la mémorisation du “code
installation” a eu lieu, avant de relâcher le poussoir
d’apprentissage;
•Relâcher le poussoir du canal du Tx maître.
CODAGE TX.
•Appuyer simultanément sur les poussoirs P1 et P2
du Tx maître utilisé pour le codage de l’installation et
les relâcher lorsque la Led clignote (au bout d’une
seconde environ);
•Approcher frontalement pour qu’ils se touchent le
Tx maître du Tx à codifier (maître ou esclave);
•Sur le Tx maître (tandis que la Ledclignote), appuyer
et maintenir dans cette position le même canal utilisé
pour le codage de l’installation: la Led s’allume
avec une lumière fixe;
•Sur le Tx à codifier, appuyer sur le canal souhaité et
le relâcher lorsque la Led s’éteint après un double
F - XT2 cod. 787005 XT4 cod. 787006
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw FAAC XT4 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van FAAC XT4 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 0,18 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info