565027
3
Verklein
Vergroot
Pagina terug
1/3
Pagina verder
17
Travel function
For the time you are absent you can select an
individual temperature. After this period the origi-
nally defi ned programme becomes active again.
Press
MENU
. Select the menu item . Confi rm
with
OK
(suitcase
appears on the display).
Select with the Button
or the end of the
travel function (= date of the recommencement of
the regular heating times). Confi rm with
OK
. Set
the time and con rm with the button
OK
. The
signal
appears on the display. Now set the
temperature and con rm with
OK
. appears
on the display. With
MENU
the function can be
deactivated.
Child lock
You can lock SPARmatic Zero to protect the
device from unauthorized activation. Press the
buttons
OK
+ at the same time for about 2
seconds until the signal
appears on the display
in order to lock the device. By using this button
combination again the symbol disappears and
you release the lock.
21
Help
Problem Cause Solution
Batteries do not have
enough power.
Replace batteries.
Heating
element
does not
warm up.
Is the boiler water
temperature O.K.?
Valve does not open,
is it calcifi ed after
the summer pause /
heating pause?
Adjust the temperature of
the boiler water.
Remove the SPARmatic
Zero, move the valve
stem back and forth per
hand or with a tool.
Heating ele-
ment does
not cool
down.
Valve does not close
completely. It may be
that the closing point
of your valve seat has
shifted.
Adapt again (see “Adapt-
ing”) Move the valve stem
several times by hand, it
may be that adaptation is
impossible because your
valve is calcifi ed or the
seat no longer performs
its function.
Pressure
piece falls
out (This can
also cause
an E1-error)
Due to an endless-
thread the pressure
piece, which is situ-
ated at the bottom,
can fall out if the
device has not been
affi xed on the valve.
Put in the pressure
piece. The device can be
adapted by pressing the
MENU
-point or by remov-
ing and inserting the
batteries. The endless-
thread is rotating now
and fi xes the pressure
piece again. Just install it
to the radiator and adapt
it once again.
-
By pressing any key the error message will
be deleted in the display and the adapter is
re-started.
18
Heating pause – Closing the SPARmatic Zero
Press
MENU
. Select the menu item with the
Button
or . Confi rm with
OK
. Select
and confi rm with
OK
. Set the temperature on
the display to
. The valve is now closed and
will work without a time programme. The calcifi -
cation protection function remains active once a
week. After the heating pause you switch in the
menu to the AUTO-mode and the personally set
programme will be executed again.
LCD standby indicator
Press
MENU
. Select the menu item with the
Button
or . Confi rm with
OK
.
Select
/
. After about 30 seconds, the LCD indica-
tor switches into standby mode. By pressing
any button, the display will be activated again.
(by removing the battery, standby mode will be
reseted). Increases the battery life time.
Going back to factory preset/All reset
Press
MENU
. Select the menu item with the
Button
or . Confi rm with
OK
. ashes,
con rm with
OK
. SPARmatic Zero is reset
again. Now, proceed as described for the initial
operation (see p. 8).
22
Problem Cause Solution
No adaptation
possible.
SPARmatic Zero is not
installed to the heater.
Is the installation OK?
Install SPARmatic Zero to
the heater.
Valve stroke is too
short.
Open and close the valve
several times manually or
replace the batteries.
Motor movement is
not possible.
Does the valve stem
move freely?
Declaration of Conformity
The Declaration of Conformity is provided at:
www.eurotronic.org
Guarantee
The three-year warranty begins on the day of
purchase. Please keep the receipt as evidence of
purchase in the future. During the guarantee pe-
riod, defective radiator thermostats may be sent
to the service address below. Please ensure suf-
cient postage is paid. A new or repaired device
will then be sent to you free of charge. Following
expiry of the guarantee, you may still send the
defective device to the address below for repairs.
Please ensure suf cient postage is paid. Repairs
carried out after the guarantee period are subject
19
Freeze protection and calcifi cation protection
function are active automatically:
Freeze protection function
If the temperature drops below 6°C, SPARmatic
Zero opens the valve until the temperature again
rises above 8°C. This prevents the radiators from
freezing.
Calcifi cation protection function
To prevent radiator valves from calcifying SPAR-
matic Zero is submitted to a calci cation protec-
tion programme once a week on Friday mornings.
Cleaning and used devices
Cleaning
To clean the SPARmatic Zero use only a dry or
lightly wet cloth. Avoid chemical solvent – it can
probably damage the device.
Used devices
Do not throw old devices and packaging into
the household waste. They can be recycled. You
receive further information at your local govern-
ment.
23
to a charge. Your legal rights are not affected by
this guarantee.
There is no new warranty period starting when
repairing or replacing the device. Please note
that we only grant warranty on the function of the
device. We will not grant warranty for the interac-
tion between the thermostat and the bottom part
of the valve. The technical data is only valid for
the use of the following valves: Heimeier, Junkers
Landys + Gyr, MNG, Honeywell, Braukmann
(measure of thread M330 x 1,5), Oventrop (M30
x 1,5) Danfoss RA, RAV and RAVL. Please see
the combinations of the devices on our website
(www.eurotronic.org/Adapter list)
EUROtronic does not issue a guarantee when
using the thermostat with valves which are not
mentioned above.
20
Adapters
Heimeier, Junkers Landys+Gyr, MNG,
Honeywell, Braukmann thread-
measure dimension of M 30x1,5
no adapter
required
Danfoss RAV (accompanying pin
must be plugged on the valve tapped)
Danfoss RA
Danfoss RAVL
Please remove all the connection pieces of the
plastic adapters before you use one of the attached
adapters!
Please completely remove the connection rods
highlighted in grey prior to assembly the adapter.
You can fi nd additional brass adapter models that
are subject to a charge: www.eurotronic.org
+ accompanying
pin, only for RAV!
Eurotronic Technology GmbH
Südweg 1
36396 Steinau-Ulmbach
Telefon: +49 (0) 66 67 / 9 18 47-0
Servicehotline: +49 (0) 66 67 / 9 18 47-17
eMail: info@eurotronic.org
Internet: www.eurotronic.org
*subject to a charge
pack.-no. 900 000 137 1 | Stand: 2013/01
3

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Eurotronic-Sparmatic-Zero

Zoeken resetten

  • Als ik de Eurotronic van de radiator neem, krijg ik meteen ADAP te zien, hij blijft dan maar heen en weer draaien. Ik kan niet ingrijpen met de menu knop. Wat doe ik verkeerd? Gesteld op 16-1-2023 om 13:26

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Eurotronic Sparmatic Zero bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Eurotronic Sparmatic Zero in de taal/talen: Engels als bijlage per email.

De handleiding is 0,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Eurotronic Sparmatic Zero

Eurotronic Sparmatic Zero Gebruiksaanwijzing - Nederlands - 2 pagina's

Eurotronic Sparmatic Zero Gebruiksaanwijzing - Deutsch - 2 pagina's

Eurotronic Sparmatic Zero Gebruiksaanwijzing - Français - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info