589517
1
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
Start Here
Type: MT500G II
Model: M-S751
© 2014 Seiko Epson Corporation
All rights reserved.
Printed in Japan, 12/14
Read these instructions before using your product.
This information is subject to change without notice.
Introduction
This product analyzes golf swings based on extensive measurements and scientic
analysis. The analysis results, which can be easily checked on your mobile device,
are useful in helping you improve your game.
The following mobile devices are supported:
iPhone 5, iPhone 5s, iPhone 5c, iPhone 6, iPhone 6 Plus, iPod touch (5th
generation) with iOS 7 or later
• Mobile device running Android™ 4.0 or later with Bluetooth SPP
What’s in the Box
M-Tracer
Micro USB
charging cable
Strap Warranty
Attachment
L size
(3 marks)
M size
(2 marks)
S size
(1 mark)
The supplied micro USB cable is designed specically for this product. Only use it
to charge this product.
The strap comes attached to the M-Tracer.
Attachment Sizes:
Size Grip circumference
L 2.44~2.71 in. (62~69 mm)
M 2.28~2.40 in. (58~61 mm)
S 2.12~2.24 in. (54~57 mm)
1. Part Names and Functions
Status LED (blue and red)
The lamp ashes to indicate the status of the product.
For more details, see the in-app help.
Charging LED (orange)
On: Charging
O: Charging complete
Top View
Bottom View
Power button
Turns the power on/o
Micro USB charging port and cover
Open the cover to charge the device.
Reset button
Strap hole
Meaning of Status LEDs
Status Display
Turning on The blue LED turns on for one second and ashes
once every two seconds.
Communicating The blue LED ashes twice every two seconds.
Turning o The blue LED turns on and then turns o.
No battery power The red LED ashes once every 5 seconds.
When turning on, the blue LED is on for one second,
then the red LED ashes once.
Pairing mode The blue and red LED ash alternately.
Error The red LED ashes once a second.
Hardware error The red LED turns on for ve seconds and then
turns o for half a second repeatedly.
Please refer to the in-app help for additional information about the LED display.
2. Charging the Battery
Before using your product for the rst time, make sure the battery is fully charged. To charge
the product, insert the USB plug into a power source.
You can use:
• Optional USB AC adapter (part number: E12E204001)
• Computer (using a USB port)
Turn o the product before charging.
Micro charging USB cable
(AC adapter not included)
The orange LED turns on when the product is charging and off when charging is
complete.
NOTE
Stop charging the product even when charging is not nished after 3 hours.
The battery may not charge correctly if you are using a charger other than the specied
AC adapter.
Charging may not nish if your computer is in Sleep or Stand-by mode.
• Connect the micro USB charging cable directly to your computer, not to a USB hub.
3.
Connecting to a Mobile Device
To use this product, you need to pair it to a mobile device using a Bluetooth
connection.
1 Place the product within 3 feet (1 m) of the mobile device.
2 With the product turned off, hold down the power button for at least five
seconds to turn on the product and enter pairing mode.
When the product is in pairing mode, the status LED ashes blue and red
alternately.
3 Turn on Bluetooth on your mobile device.
Example: [Settings] - [Bluetooth] - [ON]
4 On your mobile device, tap “MT + last 5 digits of the serial number” in the list
of detected Bluetooth devices.
(Example: MT12345)
When pairing is complete:
iOS, the status LED ashes blue twice every two seconds.
Android, the status LED continues ashing blue and red alternately. Your mobile
device displays “MT + last 5 digits of serial number” as a detected device.
NOTE
The serial number is printed on the sticker on the back of the product.
If you plan to use the product with different mobile devices, you’ll need to pair again.
4. Installing the Application
To use this product, you rst need to install Epson M-Tracer For Golf app on your
mobile device.
1 Download the app from the App Store for iOS or Google Play for Android.
2 Tap .
The Epson M-Tracer For Golf app starts.
3 Follow the on-screen instructions to register an account.
NOTE
Epson Sensing ID allows you to use multiple services and functions provided by Epson
with one ID and password.
The user is responsible for any communication charges incurred when exchanging data using
your mobile device. For information on charges and other items, contact your carrier.
5. Mounting the Product
1 Place the attachment around the grip.
First try the medium size attachment. For a thinner grip like on Ladies or
Junior clubs, try the small size attachment. For a thicker grip, try the large size
attachment.
The on the attachment should be pointing the same direction as the golf
club. If the attachment is upside-down, the attachment will become loose and
y off the club.
Center
Golf club mark
Make sure the center of the attachment is aligned with the center of the golf
club.
Slide the attachment from the shaft
onto the grip of the golf club.
If the attachment is too tight, widen it
with your nger.
Caution
Do not widen the attachment too much,
otherwise the attachment will break. If the
attachment is loose, do not use the product.
2 Put the strap around the club shaft.
Caution
Always put the strap around the club shaft.
3 Slide the product onto the attachment until it comes in contact with the
stoppers at the end.
Stopper
NOTE
Do not push too hard when the attachment is tight on the grip of the golf club.
Try a thinner grip area or a larger attachment.
• If the attachment is too loose, try a thicker grip area or a smaller attachment.
4 Make sure the product is firmly attached to the grip.
Doesnt move
back and forth
Doesnt move
around
Caution
The product should not move
when attached to the grip.
• Make sure the product is attached to the underside of the club.
• If the product is scratched while mounting, it should not aect its functioning.
6. Using the Product
1 Hold down the power button on the product for at least two seconds to turn it
on.
The blue status LED ashes once every two seconds.
2 Connect the product to your mobile device using Bluetooth.
3 Tap on your mobile device.
While your mobile device and product are communicating, the blue LED
ashes.
4 Tap Measure to start.
The red status LED turns on.
If you need to choose the type of club or shot, tap Stop, then tap Setup.
To start measuring again, tap Start.
5 Address the ball.
When the product detects that you are standing still (this takes a few seconds),
the blue status LED turns on.
Shaft
Club face
Target line
90°
90°
6 Swing the club.
After detecting the impact of the swing, the blue LED ashes and the data is
transmitted to your mobile device. The product will not measure your swing if
the impact is not detected.
Repeat steps 5 and 6 to record multiple swings.
7 When you are finished swinging, tap Stop.
8 Go to the Analysis page:
Tap Analysis on iOS.
Tap Back on Android.
9 Push the power button on the product for 2 seconds to turn it off.
The product automatically turns off when your mobile device screen is left on
any screen other than the Measurement screen for over 10 minutes.
Shaft
Attachment Grip
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Epson M-Tracer MT500GII bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Epson M-Tracer MT500GII in de taal/talen: Engels als bijlage per email.

De handleiding is 0,89 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info