675425
8
Verklein
Vergroot
Pagina terug
1/9
Pagina verder
8
LW-K400 User’s Guide
Troubleshooting
J Messages
Insert Tape No tape cartridge is installed. Turn the power o and install a
tape cartridge correctly.
Check tape! A tape cartridge which cannot be used in this product has
been set. Check the tape cartridge.
Check tape
cartridge
A tape cartridge which cannot be used in this product has
been set. Check the tape cartridge.
Check battery Possible causes for this message are:
No power remaining or inserted in the wrong way
Mixed with other types or old ones
If so, set the batteries correctly or replace them with new
ones.
Too many lines Text entered is too long.
Press
to delete the lines indicated by the cursor.
Text too long Entered text is too long for the specied tape length. Press
and adjust the tape length or make text shorter.
Seq. num. only 1
Sequence numbers have already been set. Sequence numbers can
be used for one part only.
Text will be
deleted. OK?
When creating a label with a special form,
current text will be deleted. Press to delete the text and
show the special form.
Fill every digit Entered values for barcodes are wrong. Check the entries
about values, digits, etc.
Load wider tape Unable to print on the current tape. Use a wider tape.
Txt is too long
Continue?
Entered text is too long for the specied tape length. Press
to print in the correct length.
Overheated! The printhead is too hot. Turn the power o and take out the
tape cartridge. Wait for a while before start printing again.
Cover open!
Powering o.
If you open the cover on the rear without turning the power
o, a message is displayed and then the power is turned o
automatically.
Motor error! An error occurred in the motor operation. Turn the power
o once, then turn it back on. If the same message appears,
turn the power o and contact the EPSON customer support
centre.
J
Problems
Does not operate normally.
Initialise this product if it does not operate normally such as the power cannot
be turned on or o, or the display is interrupted.
No image comes out even though has been pressed.
Are the batteries correctly set?
Check if all the batteries are correctly set.
Did the batteries run out?
Replace the batteries with new ones, or use the dedicated AC adapter
(APT0615Z).
Is the AC adapter securely connected?
Connect the AC adapter and the power cable rmly to the power socket of the
product, the AC adapter connector and the outlet.
Are you using an AC adapter other than the dedicated one?
Using an AC adapter other than the dedicated one (APT0615Z) is very
dangerous, and may cause overheating or damage to the electric circuits.
Is the display level appropriate?
Adjust the display level.
Display has turned o.
Did you enable the auto power-o function?
The power turns o automatically if no operation is made for more than
5minutes.
Did you try to carry out a function incorrectly?
If buttons are operated incorrectly, the display turns o for a moment.
Nothing is printed even though has been pressed.
Is text entered?
Nothing is printed if no text is entered.
Any message on the display?
Read the message and take the appropriate action.
Did the tape run out?
Install a new tape cartridge.
Did the batteries run out?
Replace the batteries with new ones, or use the dedicated AC adapter
(APT0615Z).
Is the cover on the rear open?
Set the tape cartridge correctly and close the cover completely.
Characters are not printed properly.
Is the tape cartridge correctly set?
Set the tape cartridge correctly.
Is the printhead dirty?
Clean the printhead.
Did the batteries run out?
Replace them with new ones, or use the dedicated AC adapter (APT0615Z).
Printing ends in the middle of text.
Did the tape run out?
Install a new tape cartridge.
Did the batteries run out?
Replace them with new ones, or use the dedicated AC adapter (APT0615Z).
Created text has gone.
Did you delete the text?
If + are pressed, the text on the display will be deleted.
Did you initialise the product?
If the product is initialised, all the created text will be deleted.
Did you remove the batteries or the AC adapter when the product was in
operation?
If the AC adapter or the batteries are removed during operation, the text may
be deleted.
Cannot attach the label.
Did you peel the backing paper?
Attach the label after peeling the backing paper.
Are you attaching it on a dirty place or on a place with a rough surface?
The label may not adhere due to the material of the attachment location or the
environmental conditions.
MEMO
If none of the above has solved the problem or the symptom is other
than the above, contact the EPSON customer support centre.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Epson LW-K400 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Epson LW-K400 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,81 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Epson LW-K400

Epson LW-K400 Gebruiksaanwijzing - Nederlands - 9 pagina's

Epson LW-K400 Gebruiksaanwijzing - Deutsch - 9 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info