543654
50
Verklein
Vergroot
Pagina terug
1/130
Pagina verder
Sub Menu Function
Direction
You can set from the following according to the way the projector is set up. s p.84
Normal, Pointing Up, Pointing Down
Operation
Direct Power On: You can set whether or not (On/Off) to enable Direct Power On.
Be careful when this item is set to On because this unit turns on at the time of power recovery with this unit plugged-in to an outlet.
Sleep Mode: When set to On, this automatically stops projection when no image signal is being input and no operations are carried
out.
Sleep Mode Timer: When Sleep Mode is set to On, you can set the time before the projector automatically turns off within a range
of 1 to 30 minutes.
Shutter Timer: When set to On, this turns off the power automatically 120 minutes after the electric shutter is closed. Shutter
Timer is set to On at the time of purchase. (When Shutter Timer and Sleep Mode are set to On at the same time, Sleep Mode has
priority.)
High Altitude Mode: Set to On when using the projector above an altitude of 1500 m.
BNC Sync Termination: Set the termination for the signal from the BNC input port. This should usually be set to Off. Set to On
when analog (75Ω) termination such as for switchers is necessary.
Remote Control Type: You can select Normal or Simple depending on the type of remote control.
Set this item to Normal to use the remote control provided with the projector. When Simple is selected, you can use the remote
control provided with other Epson projectors to operate this projector (except for EB-G5350/G5200W/G5100). This is useful if you
want to use a remote control that you are already familiar with to operate the projector.
However, you cannot use the remote control provided with the projector if this is set to Simple. Make sure you want to change this
setting to Simple because, if the projector is mounted on the ceiling or somewhere hard to reach, changing it back may be difficult.
Standby Mode
You can use the functions that monitor and control the status of the projector over the network even when the projector is in
standby mode if this is set to Communication On.
You can use
SNMP
g
to monitor and control the status of the projector over the network, or by using the EasyMP Monitor software
supplied with this product.
Air Filter Notice
You can set whether or not (On/Off) to enable Air Filter Notice. When this is set to On and a clog in the air filter is detected, the
message is displayed on the screen.
Projector ID
Set the ID within a range of 1 to 9. Off indicates that no ID is set. s p.33
Multi-screen
When this is set to On, you can adjust the hue and brightness of images projected from a row of the several projectors. s p.35
Adjustment Level: You can adjust from black to white in five stages called Level 1 to 5, and in each of these 5 levels you can
adjust Brightness Correct. and Color Correct.
Brightness Correct.: Corrects the difference in the brightness of each projector.
Color Correct. (G/R) / Color Correct. (B/Y): You can correct the difference in the color of each projector.
When Multi-screen is set to On, Auto Iris does not work.
List of Functions
50
50

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Epson EB Z8000WU bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Epson EB Z8000WU in de taal/talen: Engels als bijlage per email.

De handleiding is 5,24 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info