667126
1
Verklein
Vergroot
Pagina terug
1/1
Pagina verder
U9310020
M
M
M
M
M
P
Your thermostat has the ability to reset all settings to the factory defaults. If you
are certain you want to do this:
In standby mode(when thermostat is turned off), press and hold button
and for 5 seconds until RES is shown on LCD.
Set the Time
Configure the menu
Resetting factory defaults
Setting temperature
1) Press and hold button until the time flashes
2) Use button or to change the time
3) Press button to accept and exit
Press or once, you will see set temperature flashing. Use
or again to adjust to the
temperature you want your room
to maintain. Press button to accept
and exit.
Buttons and LCD display
Buttons Press < 5 seconds Press > 5 seconds
Turning on/off thermostat
Menu button
Increase the set value
Decrease the set value
Lock /unlock buttons
Reset to factory settings
(when thermostat is turned off)
+
+
Set the time
Confirm settings
The buttons are locked.
Displays when heating is active
Symbol Description
Set temperature
Set At
Sensor selection. This thermostat is a combination model allowing you to choose
between 3 different models. (A, AF,F )
A
model: air onl
y, with built in sensor
AF model: air & floo r , with both built in and remote sensor
F model: floor only, with remote sensor
Press and hold button for 5 seconds. Now you can see Menu 01, to proeceed to other menu, press button again. To exit menu, press button
Menu #
01
Switching differential.
Calibrate the room temperature. This feature is used to compensate for any difference
Calibrate the floor temperature. This feature is used to compensate for any difference
Set the floor temperature limit.
Select temperature format
06
07
03
04
05
02
Feature Description
Factory Default
Feature Value
0
°C
40
°C
20
°C ~
40
°C
°C
/
°F
°C
A / AF / F A
Press or to select
The numbers of degree difference before switching.
between the displayed room temperature and a thermometer.
between the displayed floor temperature and a thermometer.
This feature is to protect the floor surface.
°C or °F.
The default is 1°C which means the thermostat will switch the
heating on
0.5°C below the set temperature and will turn it off 0.5°C above the set temperature.
With a 2°C differential,
the heating will switch on 1°C below the set temperature
and will switch off 1°C above the set temperature.
1°C 1°C ~ 5°C
-5°C ~ +5°C
0
°C
-5°C ~ +5°C
Installation and Wiring
Carefully separate the front half of the thermostat from the back plate by placing a
small flat head terminal driver into the slots on the bottom face of the thermostat.
Carefully unplug the ribbon connector which is plugged in to the front half of the thermostat.
Place the thermostat front half somewhere safe. Terminate the diagrams below.
Screw the thermostat back plate on to the back box.
Re-connect the thermostat ribbon cable and clip the two halves together.
CS-11 LCD Digital Thermostat
Registered Address: 6 Tannery Yard, Witney Street, Burford, Oxon., OX18 4DW
Tel: 01993 824900 : www.emmeti.co.uk : e: sales@emmeti.co.uk
Frost protection. This is to avoid room temperature goes below 5°C. on / off off

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Emmeti CS-11- U9310020 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Emmeti CS-11- U9310020 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Emmeti CS-11- U9310020

Emmeti CS-11- U9310020 Installatiehandleiding - English - 1 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info