708661
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
INTRODUCTION
The code lock AG40KE11B is designed for use in combinaon with the Home Alarm System AG400011. By using
a 4-digit access code you can turn the alarm system armed, parally armed and disarmed. In addion, a panic
alarm can be acvated.
Transmission
Low Baery
Code Confirmaon
Arm
Disarm
PARM1
PARM2
INSERTING THE BATTERY
To insert the baery, first remove the mounng plate by unscrewing the (a) screw on the boom of the unit.
Next, unscrew the two screws of the baery plate (b) on the back of the unit. Then insert the included 9-volt
baery (c) in the compartment and screw the baery plate back on.
MOUNTING PLATE
Use the mounng plate you unscrewed in the previous step as a
template to mark the drill holes on the wall. Aer drilling the holes,
fix the mounng plate to the wall with the included wall plugs and
screws. When you have completed configuraon, you can place the
keypad back in the mounng plate and screw it back in with the
screw (a) on the boom.
ADDING THE WIRELESS KEYPAD TO THE HOME ALARM SYSTEM AG4000
1. On the alarm panel, enter the alarm panel’s PIN (1234 by default) + DISARM to disarm the system.
2. Enter PIN (1234 by default) + 15 + PARM to start the binding process. The DISARM LED will start to
blink for 30 seconds with a beep tone. Within 30 seconds, set the remote keypad to enter binding mode by
using the tamper switch (d) on the back.
3. If the remote keypad is added successfully, the DISARM LED will turn on for 1 second along with a long
beep sound. If the binding process fails, it will meout aer 30 seconds and 3 short beeps will be heard. To
exit the binding process, press the DISARM key on the alarm panel.
CHANGING THE ACCESS CODE
For security, it is highly recommended that you change the standard PIN (1234) to a four-digit PIN of your own
choosing. The system can support one master user code, and five user access codes.
* To set a new master access code take the following steps
1. Press followed by the standard PIN (1234) and again .
The LED will now light up and flash three mes.
2. Choose a new four-digit PIN and enter this now, followed by . The LED will now light up and
flash four mes to confirm. The master access code has now been changed.
* To set user access codes, take the following steps
1. Press followed by the master access code you have set in the previous step and then again .
The LED will now light up and flash three mes.
2. Enter (for user code 1) followed by and then the four-digit user access code you wish to set,
followed by . The LED will now light up and flash four mes.
3. To set user access codes 2-5, simply repeat the above steps but replace the with a number 2-5.
Note: The user access codes will only apply to the remote keypad. When operang the home alarm system from
the main alarm panel, you will sll need to use the PIN you have set for that.
TESTING THE REMOTE KEYPAD
To fully arm the system: Enter [your access code] followed by
Parally arm the system: Enter [your access code] followed by or
To disarm the system: Enter [your access code] followed by
Your buon presses will be confirmed by the lighng up. It is important you also confirm the
transmission of the code once you have finished entering the command by seeing if the is flashing. When
first seng up the system, we recommend you test it near the main alarm panel so that you can confirm the
keypad successfully transmied by seeing the alarm mode change on the alarm panel and hearing a beep tone.
PANIC SIGNAL
The remote keypad allows you to send a panic signal, for instance because you are using the remote keypad
under duress. To send a panic signal, press and hold the and at the same me for at least two
seconds and unl the LED is flashing rapidly.
DISABLING THE REMOTE KEYPAD
If a sequence of more than 16 incorrect key presses is entered, the keypad will be disabled for 1 minute. If the
keypad is consecuvely disabled 3 mes, the keypad will send a tamper signal to the alarm panel and the
LED will flash slowly.
Note: When the keypad is disabled for 1 minute, the LED will flash slowly, indicang that the Keypad is
temporarily shut down. During this minute, any key presses will be treated as an invalid input. Aer 1 minute
has elapsed, correct input will be accepted again.
2
2
2
1
1
1
1
1
1
(a)
(b)
(c)
UP
(a)
Tamper
switch
(d)
-1- -2-
2
1
1
2
3
4
5
6
7
8 9
0
2

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Elro-AG40KE

Zoeken resetten

  • Hallo, ik heb een codeslot bij de achterdeur in gebruik. Is het mogelijk dat deze ook een signaal geeft als het alarm wordt ingeschakeld.
    Zoals wanneer de code wordt ingetoetst op het grote scherm. ( dan hoor je deze aftellen) Gesteld op 6-2-2022 om 16:17

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elro AG40KE bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elro AG40KE in de taal/talen: Engels als bijlage per email.

De handleiding is 2,02 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Elro AG40KE

Elro AG40KE Gebruiksaanwijzing - Nederlands - 2 pagina's

Elro AG40KE Gebruiksaanwijzing - Deutsch - 2 pagina's

Elro AG40KE Gebruiksaanwijzing - Français - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info