708646
5
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
4. The system should arm successfully using the new PIN code.
Perform a quick test after the system has been set up and configured.
1. First disarm the system using the app
2. Re-arm the system using the app
3. Trigger an alarm using the PIR and door/window detector.
4. Use the remote control to turn off the alarm once it has been triggered.
5. Check the notifications to ensure that they are correct.
Note: To conserve its battery life, the PIR Motion sensor can be triggered only once every 2
minutes.
Daily operations from alarm panel:
Function Button Icon Remark Action
Arm
Activates the alarm for monitoring. Enter (PIN code) +
Disarm
Deactivates the alarm.
Enter (PIN code ) +
Alarm Panel
Selecting a suitable location:
Mount the alarm panel close to the door which you normally use to enter/exit your house.
Note that the alarm panel requires a power outlet to function properly.
Ensure the location selected has good GSM
reception. You can do this by cross checking the
signal bar on your phone at that location.
The panel must not be located or operated in
conjunction with any other nearby transmitter or
antenna.
1. Remove the back panel mounting bracket of the alarm panel and mount the bracket on the
wall using wall anchors and screws.
2. Once secured, ensure the power is connected and reattach the alarm panel to the secured
mounting bracket.
Door/Window contact
If possible, locate sensors within 100 ft. (30m) of the panel. While a transmitter may have a range
of 350 ft. (106 m) or more out in the open, the environment at the installation site can have a
significant effect on transmitter range
1. Mount the sensor on the door frame and the
magnet on the door. If the sensor is used on
double doors, mount the sensor on the least-
used door and the magnet on the most-used
door.
2. Place sensors at least (1.5 m) above the floor to
ensure the best transmission range.
3. Make sure the alignment arrow on the magnet
points to the alignment mark on the sensor.
4. Avoid mounting sensors in areas where they
will be exposed to moisture or high
temperatures.
5. Use spacers (not included) to keep sensors and
magnets away from metal or metallic surfaces
such as foil wallpaper.
PIR Motion Sensor
The recommended position for a PIR Detector is in the corner of a room mounted at a height
between 1.8 and 2m. At this height, the detector will have a range of up to 10m with a field of view
of 110° (see figure below).
Keep sensors within 30 m (100 ft) of the alarm panel.
Step 13 – Final test before mounting the system
Step 14 – Mounting the system
9
1
3
5
7
Corner mounted
5

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Elro-AG400011---Home-Alarm-System

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elro AG400011 - Home Alarm System bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elro AG400011 - Home Alarm System in de taal/talen: Engels als bijlage per email.

De handleiding is 1,59 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Elro AG400011 - Home Alarm System

Elro AG400011 - Home Alarm System Snelstart handleiding - Nederlands - 5 pagina's

Elro AG400011 - Home Alarm System Gebruiksaanwijzing - Nederlands - 236 pagina's

Elro AG400011 - Home Alarm System Snelstart handleiding - Deutsch - 5 pagina's

Elro AG400011 - Home Alarm System Gebruiksaanwijzing - Deutsch - 12 pagina's

Elro AG400011 - Home Alarm System Gebruiksaanwijzing - English - 15 pagina's

Elro AG400011 - Home Alarm System Snelstart handleiding - Français - 9 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info