668435
26
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
Elma DT5500A
side 26
d)Being free from the TEST button or pushing down the TESTbutton in the LOCK
status can exit from the LOCK status and shutoff the high-voltagesynchronously, the
resistance values is indicated in the primary display will be held, and the secondary display
still be in the status of monitoring the insulation voltage for the tested.
e)Subsequently, discharge the balance insulation voltage of the tested through the inner
switch of the meter. Turning the function switch can exit automatically from testing status
during the process
Low resistance (continuity) measurements
a). Set the range switch to 400Ω/BZ Position
b). Connect the red test lead to the V Ω terminal and black to the COM terminal.
c). Connect the tips of the test leads to both ends of the circuit under test. read resistance
in Ω on the LCD. The two ranges(40.00/400.0Ω) can be switched automatically; the
primary display of the resistance in Ω, flashes in synchronous with the analog bar.
d). When the impedance on circuit is below approximately 35Ω.It will indicate by a
continuous beeper.
e) The current is from 200 to 220mA while the tested resistance is 0Ω
f) The high voltage symbol “ “ flashes along with a primary display of “>30V” and the
buzzer warns frequently if the voltage (AC/DC) is more than 30V.
AC/DC Voltage measurements
a). Set the range switch to ACV or DCV position
b). Connect red test lead to “V Ω” terminal and black test lead to terminal “COM”.
c). Connect test prods of test leads IN PARALLEL to the circuit being measured.
d). Read the voltage value on LCD.
Power tools and small appliances
This test would also apply to other similar equipment that has a line cord. For double
insulated power tools, the megohmmeter lead shown connected to the housing would be
connected to some metal part lf the tool(e..g chuck,blade).
Note:The switch of the device must be in the “ON”position and the main power should be
disconnected.
Motors
AC-Disconnect the motor from the line by disconnecting the wires at the motor terminals
or by opening the main switch. If the main switch is used and the motor also has a starter
then the starter must be held, by some means, in the “ON” position. In the latter case, the
measured resistance will include the resistance of the motor, wire and all other
components between the motor and the main switch. If a weakness is in dicated, the motor
and other components should be checked individually. If the motor is disconnected at the
motor terminals, connect one megohmmeter lead to the grounded motor housing and the
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elma DT5500A bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elma DT5500A in de taal/talen: Engels, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 1,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info