741487
19
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
(((ELKRON)))
MP110 USER MANUAL
(((ELKRON)))
MP110 USER MANUAL
2.Access Codes
The unit can be programmed so as to enable User 2 (e.g., service
personnel, custodian, porter , telemonitoring, private vigilance, etc)
to have his own secret access code which allows him to arm/disarm
the unit without performing other operations.
The unit identifies up to a maximum of 8 different assigned codes and
as many users:
After entering a correct code that is enabled, the unit’s buzzer beeps
twice, or it beeps once at length to indicate an error. The Master user’s
code is always enabled; the other codes must instead be enabled (refer
to par. “Code Enabling”).
If the engineer’s code is enabled, it remains enabled until the Master
user’s code is again entered to partially or totally arm the system, or
until the first arming by electronic key-
Once armed, every re-entry/EXCLUDED display procedure triggers a
1-minute delay (that is reset each time the key is pressed). If a delay
time-out occurs, the procedure is exited automatically without saving
the changes made.
• Each time the key is pressed on the KP100 keypad (segmented
display), while entering the secret code, a segment of the display lights
up to display the digits (entered) as they are typed in.
FACTORY
CODE
CODE 1 - MASTER USER 1 11111
CODE 2 - USER 2 2 22222
CODE 3 - ENGINEER 3 33333
CODE 4 - TELEMONITORING 4 44444
CODE 5 - USER 5 5 55555
CODE 6 - USER 6 6 66666
CODE 7 - USER 7 7 77777
CODE 8 - USER 8 8 88888
Each user is assigned and “identification
number “ (from 1 to 8) that is to be typed
in before the code; this number allows
the unit to identify the user of the system.
To be identified by the system, the owner
must type in the number 1 followed by
his personal code; any other users will
instead type in the number 2, 3, 4, 5, 6,
7 or 8, followed by his personal code
19
3. System Arming/Disarming
For ARMING of the system, enter a valid code associated to the 3
sectors and press the
TOTAL
key.
Leds
1
3
,
2
and
3
flash, and after 4 seconds they
light up with a fixed light.
If there is an an exit delay, it is indicated by the intermittent sound of the
buzzer.
To DISARM the system, enter a valid code and press the
TOTAL
key.
Leds
1
3
,
2
and
3
corresponding to active sectors
go OFF and thebuzzer beeps twice.
To partially ARM the system, enter a valid code and press the key for
the zone or zones ne wishes to arm.
1
to arm Zone 1 - the Led
1
3
flashes and lights up with a fixed
light after 4 seconds
2
to arm Zone 2 - the Led
2
flashes and lights up with a
fixed light after 4 seconds
3
to arm Zone 3 - the Led
3
flashes and lights up with a fixed
light after 4 seconds
To DISARM the system, enter a valid code and press the
TOTAL
key. The
leds in the previously armed zones go OFF and the buzzer beeps twice.
During partial arming, about 5 seconds are available (led flashes) within
which it is possible to correct the type of arming; once this time is up,
the leds light up with a fixed light and the sectors are armed.
• After selecting the desired configuration for the zones, arming is
confirmed by pressing the
A
key without waiting for the time
available for arming to expire.
3.1 Away Arming/Disarming
3.2 Partial Arming/Disarming
22
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elkron MP110MTG bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elkron MP110MTG in de taal/talen: Engels als bijlage per email.

De handleiding is 0,44 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Elkron MP110MTG

Elkron MP110MTG Gebruiksaanwijzing - Deutsch - 32 pagina's

Elkron MP110MTG Gebruiksaanwijzing - Français - 120 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info