741423
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
ALIMENTATORE PS515
PS515 POWER SUPPLY
ALIMENTATEUR PS515
ITALIANO
DESCRIZIONE GENERALE
L’alimentatore PS515 è costruito in riferimento alla norma EN 50131-6.
L’impostazione di fabbrica della tensione di uscita (14,4V) tiene conto
della caduta di tensione di 0,6 / 0,7V ai capi del diodo di protezione
presente in molte centrali di allarme e nella quasi totalità delle centrali
Elkron.
Alimentatore in CAT II 2500 V. L’alimentatore che, una volta installato, è
soggetto a tensioni transitorie superiori a quelle della categoria di
sovratensione di progetto, necessita di una protezione supplementare
delle tensioni transitorie esterne all’apparecchiatura.
CARATTERISTICHE TECNICHE
Tensione d’ingresso ....................................... 220-240V~ ; 50/60Hz ; 0,6A
Tensione di uscita ........................................... 14,4V
Corrente max erogabile ................................... 1,5A
Ripple max ...................................................... 300mVpp
Fusibile ........................................................... T2AL 250V~
I cavi impiegati devono rispondere alla norma IEC 60332-1-2 se di
sezione 0,5 mm² o superiore, oppure alla norma IEC 60332-2-2 se di
sezione inferiore a 0,5 mm².
NOTA: Il morsetto “C” (test), se forzato a 0V (massa) porta la tensione di
uscita a 11V circa per consentire il controllo batteria (per le centrali di
allarme predisposte o che prevedono la gestione di questa funzione).
LEGENDA SIMBOLI
Simbolo
Spiegazione
Tensione di alimentazione continua
~
Tensione di alimentazione alternata
Alimentatore dotato di un doppio isolamento
Riferirsi al manuale d’installazione del dispositivo
ELKRON
Tel. +39 011.3986711 - Fax +39 011.3986703
www.elkron.com mail to: info@elkron.it
ENGLISH
FRANCAIS
GENERAL INFORMATION
The PS515 power supply is manufactured with reference to the EN50131-6
standard.
The output voltage set to 14,4V considers the voltage drop (0,6 / 0,7V)
across the protection diode usually mounted on the alarm control panels,
and in particular on the Elkron control panels.
Power supply in CAT II 2500 V. Once installed, the power supply is subject
to transient voltages higher than those of the overvoltage category for
which is was designed. For this reason, an additional transient voltage
protection is required outside the device.
TECHNICAL CHARACTERISTICS
Input Voltage ................................................. 220-240V~ ; 50/60Hz ; 0,6A
Output Voltage ................................................. 14,4V
Max Output Current ......................................... 1,5A
Max Ripple ....................................................... 300mVpp
Fuse ................................................................ T2AL 250V~
Wires with cross-section area of 0.5 mm² or larger must comply with
IEC 60332-1-2; wires with cross-section area smaller than 0.5 mm² must
comply with IEC 60332-2-2.
NOTE:
When connected to 0V (ground), the “C” terminal brings the output voltage
to roughly 11V in order to allow the battery test (for the alarm control
panels providing this function).
KEY TO SYMBOLS
Symbol
Description
Direct input voltage
~
Alternating input voltage
Power supply fitted with double insulator
See the installation manual of the device
DESCRIPTION GÉNÉRALE
L’alimentation PS515 est construite en référence à la norme EN50131-6.
Le réglage d’usine de la tension de sortie (14,4V) tient compte de la
chute de tension de 0,6 / 0,7 V aux extrémités de la diode de protection
présente dans de nombreuses centrales d’alarmes et dans la presque
totalité des centrales Elkron.
Alimentation en CAT II 2500 V. L’alimentateur, qui une fois installé peut
subir des tensions transitoires supérieures à celles de la catégorie de
surtension de projet, nécessite une protection supplémentaire des
tensions transitoires externes à l’équipement.
CARACTÉRISTIQUES TECHNIQUES
Tension d’entrée ............................................ 220-240V~ ; 50/60Hz ; 0,6A
Tension de sortie ............................................ 14,4V
Courant max. fourni......................................... 1,5A
Ondulation max. .............................................. 300mVpp
Fusible ............................................................ T2AL 250V~
Les câbles utilisés doivent satisfaire la norme IEC 60332-1-2 si la
section mesure au moins 0,5 mm², ou la norme IEC 60332-2-2 si la
section mesure moins de 0,5 mm².
REMARQUE :
La borne « C » (test), si forcée à 0 V (masse) porte la tension de sortie à
11 V environ, afin de permettre le contrôle de la batterie (pour les
centrales d’alarmes prévues ou qui prévoient la gestion de cette fonction).
LÉGENDES SYMBOLES
Symbole
Explication
Tension d’alimentation continue
~
Tension d’alimentation alternée
Alimentation à double isolement
Se reporter au manuel d’installation du dispositif
DS80PS42-001B LBT80110
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elkron DS80PS42 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elkron DS80PS42 in de taal/talen: Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 0,33 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info