741418
7
Verklein
Vergroot
Pagina terug
1/18
Pagina verder
DS80MM1L-001 7
Management of alarms generated by shocks/vibrations
The detection of the alarm generated by impulses caused by shocks or vibrations can be configured as follows.
Single pulse detection
The alarm is generated by the detection of a single pulse exceeding the set threshold.
Multiple pulse/sum of vibrations detection
The alarm is generated by the detection of at least one of the following two conditions:
I. When 3 pulses are detected in a time interval of less than 20 seconds.
II. When the accumulation of vibrations detected in a time interval of less than 2 minutes exceeds the set threshold.
The modes described are determined by jumper JP3:
If the jumper is ON (the jumper is inserted on the two pins): Single pulse detection (default setting)
If the jumper is OFF (jumper removed or "arranged" on a pin): Multiple pulse/sum of vibrations detection
Sensitivity adjustment
Jumpers JP4 and JP5 can be used to determine the sensitivity required to generate a shock or vibration alarm. See the
following table:
Battery
The device is powered by a CR123A 3 V lithium battery and can indicate when the battery is flat. When the battery charge is
low, the device sends a signal to the control unit together with the normal transmissions.
When the battery is flat, the device does not work and the LED blinks every 4 seconds.
The battery is pre-installed at the factory with the insertion of an insulating element. Remove the insulation from the battery to
activate the device.
Tamper protection
The tamper switch protects the device from tampering attempts or attempts remove it from the installation surface.
Supervision
In normal operation, the device transmits a supervision signal to the control unit at regular intervals during normal operation.
The control unit generates a supervision alarm if the control unit does not receive the device signal within the predetermined
time.
Test
Whenever the Test button is pressed, the device transmits a signal to the control unit to test the radio range and
activates Test mode for 3 minutes.
In Test mode, the LED lights up whenever an alarm is generated.
Test mode is extended by 3 more minutes if the Test button is pressed again.
Preparation
Step 1: Remove the battery insulation.
Step 2: Enable the learning function on the control unit (see the respective manual for more details).
Step 3: Press the Test button on the device to send a signal to the control unit.
Step 4: If the control unit receives the signal correctly will respond by emitting beeps. Refer to the manual of the control unit
to complete the learning process.
Step 5: After the device has been learnt, set the control unit to "Walk Test" mode, by holding the device in the desired
position and press the Test button to check that it is within the wireless range of the control unit.
Step 6: After having checked the correct position of the device, proceed with the installation.
JP4 JP5 Sensitivity
ON OFF Low
OFF ON
Medium (default)
ON
ON
High
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elkron DC600S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elkron DC600S in de taal/talen: Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 0,65 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Elkron DC600S

Elkron DC600S Snelstart handleiding - Deutsch, English, Français, Italiano - 8 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info