471228
8
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
11
Mounting
Expansion wall plugs are provided to secure the hood to most
types of walls/ceilings. However, a qualified technician must
verify suitability of the materials in accordance with the type of
wall/ceiling. The wall/ceiling must be strong enough to take
the weight of the hood. Do not tile, grout or silicone this
appliance to the wall. Surface mounting only.
Description of the hood
Fig. 1
H. Interconnection cable
K. Control lever
Attention! The control lever is already supplied. It is to
be installed last, before connecting the hood to the
mains.
Insert the control lever into the apposite housing (see
drawings on the first pages of this booklet - triggered
connection, compulsory direction.
L. Halogen bulb
M. Lateral filter holder frame
N. Active carbon filter
O. Metal anti-fat filter
P. Anti-fat and carbon filters holder frame
Q. Filter holder frame releases
Operation
Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
The hood is equipped with a “TOUCH SENSOR” device able
to determine the control of the lights and the speed when the
user touches the control bar. Read the instructions below
carefully for this purpose.
The cooker hood can be controlled through a remote control
available as accessory kit (see the paragraph relating to the
functioning of the remote control).
Automatic switch-on function
The hood is equipped with a temperature sensor that starts
the motor at the 1st suction speed (power) when the room
temperature around the hood is higher than 70°C.
The user can, however, switch off or modify the suction speed
(power). (See paragraph “Control of suction speed (power))”.
Control of suction speed (power)
The selection of the suction speed (power) is cyclical,
according to the speed sequences “”stand-by - 1-2-3-4- Stand
by -1-2-”… so that at every touch of the UPPER PART of the
control bar the suction speed (power) increases by a level
and then to switches off (stand-by) if the control bar is touched
again when the hood is at suction speed (power) 4.
It is possible lo turn the hood off (standby) even when the
hood is at any speed by pressing the UPPER PART of the
control bar (for more than 3 seconds).
It is possible to determine what suction speed (power) the
hood is in when the bar is equipped with a led that changes
colour on the basis of the suction speed (power), as follows:
Hood in stand-by: LED OFF
1st suction speed (power) - led GREEN
2st suction speed (power) - led ORANGE (amber)
3st suction speed (power) - led RED
4st suction speed (power) - led RED (FLASHING)
Note: the 4
th
aspiration speed (power) remains on for 5
minutes after which the aspiration motor positions itself on the
2
nd
speed.
Touched once more, the suction motor switches off (Stand-
by).
Need to wash the anti-fat filter: GREEN led FLASHING
(read the instructions relative to “Reset and configuration of
the filters saturation signal")
Need to wash or replace the carbon filters: ORANGE
(amber) led FLASHING (read the instructions relative to
“Reset and configuration of the filters saturation signal”)
Note: reset can be carried out both with the control lever and
the remote control.
Control of the central light
The central light can be switched on and off by touching the
LOWER PART of the control bar BRIEFLY.
Control of the lateral lights (when envisaged)
The lateral lights can be switched on and off by touching IN A
PROLONGED MANNER the LOWER PART of the control
lever.
The PROLONGED TOUCH allows, other than switching on
and off, adjusting the intensity of the light emitted by the lamp.
Note: The functions of switching and off (and adjustment)
alternate.
The light intensity regulation feature is not available for hoods
with neon lights.
Reset and configuration of the filters saturation signal
Switch the hood on at any speed (see paragraph above
“Selection of the suction speed (power)”
Reset anti-fat filter saturation signal (GREEN LED
FLASHING on the control level)
First proceed with the maintenance of the filter as
described in the corresponding paragraph.
Touch in a prolonged manner (more than 3 seconds) the
UPPER PART of the control lever, the LED stops flashing to
indicate that the reset of the signal has been carried out and
the hood switches off.
Reset anti-fat filter saturation signal ORANGE (amber)
LED FLASHING
First proceed with the maintenance of the filter as
described in the corresponding paragraph.
Touch in a prolonged manner (more than 3 seconds) the
UPPER PART of the control lever, the LED stops flashing to
indicate that the reset of the signal has been carried out and
the hood switches off.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Elica-Star

Zoeken resetten

  • Kan ik iemand vinden in België - Oost Vlaanderen of in Nederland die een Elica dampkap type STAR kan repareren ?
    Ik heb een kortsluiting gehad door losse draadjes in één van de lampen en nu werkt het ganse toestel niet meer.
    Alvast dank Gesteld op 22-5-2016 om 11:31

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elica Star bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elica Star in de taal/talen: Engels als bijlage per email.

De handleiding is 1,42 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Elica Star

Elica Star Gebruiksaanwijzing - Nederlands, Deutsch, Français, Italiano, Português, Espanõl, Polski, Türkiye, Dansk, Svenska, Norsk, Suomi - 88 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info