561010
22
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
Explanatory Note on Specifications 19
On the rear of this manual (respectively attachment) you will find the specifications of your loudspeaker
Specifications include:
- Dimensions Height x Width x Depth (in mm)
- Weight (in kg)
- Principle
- Driver Units: number and type of drivers
- Mains Fuse / Mains Voltage
- Max. Power Consumption, Full Output
- Crossover Frequency
- Frequency Range (in hertz)
- Max. amplifier power
- S/N (A-weighted)
- Inputs
- Input sensitivity
- Input impedance
Dimensions refer to the outer dimensions of the loudspeakers.
The Weight indicates the total weight of the loudspeaker without packaging and without accessories (like mains
cable etc.). Due to material tolerances, this value may vary by 10 percent.
The Principle describes the acoustical and electrical concept on which the speaker is based on (e.g. closed box
or bass reflex, powered (= with amplifier built-in).
Drive Units give information on the number and type of drivers of a loudspeaker.
The correct Mains Voltage, measured in volts, is necessary for a proper function of your appliance and is pro-
vided by your local power authorities. The mains voltage might vary between the given values. The technical data
of the Fuse give the current- and voltage values which the fuse should have at the given mains voltages.
Max. Power consumption, full output specifies the power, measured in watts, which is drawn out of the mains
when the appliance works with maximum output levels.
The Crossover Frequency is defined by the built-in (active) crossover network which adapts the overlay between
collocated drivers.
The Reproduction Range of a loudspeaker is defined by the upper and lower cut-off frequencies of the SPL fre-
quency response. At the cut-off frequencies the sound pressure level decreases by 8 dB (factor 2.5) as compared
to the midrange. Given a standard domestic room, the effective lower cut-off frequency may deviate from stan-
dard values due to room resonances.
The Max. amplifier power of an amplifier is also measured in watts and specifies the power which can be repro-
duced by the amplifier without any disturbances, like humming, noise or distortions. It is differentiated between the
sine power and the pulse power. The sine power describes the power which the amplifier can reproduce for an
endless time theoretically, the pulse power is even higher and specifies the power for short term signals which
can be handled by the amplifier without distortions.
The signal to noise ratio (S/N (A-weighted)) describes the relation between the wanted signal and not wanted
signals like noise or humming. Normally it is measured in dB and is weighted with a curve called “A”-curve which
describes the sensitivity of the human ear.
Inputs lists the available inputs and their connector specifications.
The Input sensitivity is measured in volts normally and lets you know the input voltage which is needed to drive
the amplifier to full level.
The Input impedance is the AC resistance, normally measured in kilo-ohms, which represents the load for the
driving pre amplifier.
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elac AM 180 - Active Monitor bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elac AM 180 - Active Monitor in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 1,85 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info