Retighten the locking grip (14) to secure the
turntable (17) in place.
Cut as described under section 7.1.
7.3 Miter cut 0°- 45° and turntable 0° (Fig. 1-3, 32)
The crosscut saw can be used to make miter cuts of
0° - 45° in relation to the work face.
If necessary, dismantle the clamping device (8) or
mount it on the opposite side of the fixed saw
table (18).
Move the machine head (4) to its upper position.
Fasten the turntable (17) in 0° position.
Undo the locking screw (22) and use the handle
(1) to tilt the machine head (4) to the left until the
pointer (20) coincides with the required value on
the scale (19).
Retighten the locking screw (22) and make the
cut as described in section 7.1.
7.4 Miter cut 0°- 45° and turntable 0°- 45°
(Fig. 1-3, 33)
The crosscut saw can be used to make miter cuts to
the left of 0°- 45° in relation to the work face and, at
the same time, 0° - 52° to the left or 0° - 60° to the
right in relation to the stop rail (double miter cut).
If required, dismantle the clamping device (8) or
mount on the opposite side of the fixed saw table
(18).
Move the machine head (4) to its upper position.
Release the turntable (17) by slackening the
locking grip (14).
Use the handle (1) to adjust the turntable (17) to
the angle required (in this connection see also
section 7.2).
Retighten the locking grip (14) to secure the
turntable in place.
Undo the locking screw (22) and use the handle
(1) to tilt the machine head (4) to the left until it
coincides with the required angle value (in this
connection see also section 7.3).
Re-tighten the fixing screw (22).
Cut as described under section 7.1.
7.5 Limiting the cutting depth (Fig. 34)
The cutting depth can be infinitely adjusted using
the screw (34). To do so, undo the knurled nut on
the screw (34) and move the stop for the cutting
depth limiter (35) to the outside. Turn the screw
(34) in or out to set the required cutting depth and
then retighten the knurled nut on the screw (34).
Check the setting by completing a test cut.
7.6 Chip box (Fig. 35-36/Item 23)
The saw is equipped with a chip box (23) for sawdust
and chips. The chip box (23) can be fitted onto the
extractor adapter (33).
To empty the chip box (23), flip the box open as
shown in Figure 36 and carefully empty it by tapping.
Alternatively, a suitable dust extraction device can be
fitted to the extractor adaptor (33).
7.7 Changing the saw blade (Fig. 1, 37-40)
Pull out the power plug!
Swing the machine head (4) upwards and lock in
this position with the fastening bolt (27).
Press the release lever (3) and swing up the saw
blade guard (6) to the point where the recess in
the saw blade guard (6) is above the flange bolt
(39).
Press the saw shaft lock (5) with one hand while
holding the wrench (P) on the flange bolt (39) with
the other.
Firmly press on the saw shaft lock (5) and slowly
rotate the flange bolt (39) in clockwise direction.
The saw shaft lock (5) engages after no more
than one rotation.
Now, using a little more force, slacken the flange
bolt (39) in the clockwise direction.
Turn the flange screw (39) right out and remove
the external flange (40).
Take the blade (7) off the inner flange and pull out
downwards.
Carefully clean the flange screw (39), outer flange
(40) and inner flange.
Fit and fasten the new saw blade (7) in reverse
order.
Important. The cutting angle of the teeth, in other
words the direction of rotation of the saw blade
(7) must coincide with the direction of the arrow
on the housing.
Check to make sure that all safety devices are
properly mounted and in good working condition
before you begin working with the saw again.
Important. Every time that you change the saw
blade, check to see that it spins freely in the table
insert (12) in both perpendicular and 45° angle
settings.
Important. The work to change and align the saw
blade (7) must be carried out correctly.
25
GB
