831577
18
Verklein
Vergroot
Pagina terug
1/110
Pagina verder
GB
- 18 -
5) onto the lower push bar, then push the
lower push bar onto the engine unit (Fig. 6a/
Item 3) as shown in Fig. 6a and secure with
the screws (Fig. 6b/Item 9) and the star nuts
(Fig. 6b/Item 8).
Push the top push bar (Fig. 7a/Item 1) onto
the lower push bar (Fig. 7a/Item 2) and se-
cure with the screws (Fig. 7a/Item 9) and the
star nuts (Fig. 7a/Item 8).
Fit the two-hand safety switch on the top push
bar as shown in Fig. 7b and 7c.
Fasten the cable with the 2 cable securing
clamps (Fig. 8/Item 7) to the push bars.
Power supply
The machine can be connected to any light
socket-outlet (with 230 - 240 Volt alternating cur-
rent). However, the socket outlet must have an
earthing contact protected by a 16 A circuit brea-
ker. Additionally, a residual current device (RCD)
circuit-breaker with max. 30 mA must be used!
Power cable for the device
Please only use power cables that are not dama-
ged. The total length of the power cable should
not exceed 50 meters; going beyond this distance
will reduce the power output of the electric motor.
The power cable must have a cross-section of 3 x
1.5 mm2. The insulating sheath of such machines
is frequently damaged.
Some of the causes for this are:
Cracking due to old age of the insulation
Kinking caused by improper fastening or
guidance of the power cable
Even though power cables with damaged insula-
tion sheaths pose a lethal hazard, some people
still use them. Do not make this mistake! Cables,
plugs and socket couplers must meet the fol-
lowing requirements listed below. Power cables
used to connect machines must have a rubber
insulation sheath.
The power cables must, at the very minimum, be
of type HO5RN-F and 3-stranded. The cable type
must be printed somewhere on the power cable.
Only purchase power cables that are marked!
Plugs and socket couplers for the power cables
must be made from rubber and splash-proof.
There is a limit to how long power cables can be.
Longer power cables require larger conductor
cross-sections. Power cables and connecting li-
nes must be regularly checked for damage. Ensu-
re that the lines are de-energized before checking
them. Completely unwind the power cable. Also
check power cable entry points, plugs and socket
couplers for kinks.
6. Operation
6.1 Starting up
Connect the machine’s power supply cable (Fig
9/ Item B) to the plug (Fig. 9/Item A) and secure
the power cable with the strain-relief clamp (Fig
9/Item 5).
Danger! To prevent accidental start-up of the ma-
chine, the push-bar is equipped with a two-point
switch (Fig. 10/Item A) which must be pressed
before the lever switch (Fig. 10/Item B) can be
pressed. If the lever switch is released, the machi-
ne switches o . Repeat this process several times
so that you are sure that your machine functions
properly. Before you perform any repair or mainte-
nance work on the machine, ensure that the hoe
blades are not rotating and that the power supply
is disconnected.
The equipment must be moved into operating
position before you begin with your work. First pull
the locking pin (Fig. 11/Item A) in the direction of
the arrow as shown in Fig. 11 and swing up the
wheel unit until the locking pin engages again in
position B. Proceed in reverse order to move the
equipment into transport position.
Always ensure that a safe distance (provided
by the long handles) is maintained between the
machine and the user. Be especially careful
when changing direction on slopes and inclines.
Maintain a solid footing and wear sturdy, non-slip
footwear and long trousers. Always work along
the incline (not up and down).
Use special caution when backing up and pulling
the machine (tripping hazard).
6.2 Tips for proper working
Place the machine in front of the area you wish to
hoe and hold it securely on the push bar before
you switch on the machine. Guide the hoe blades
over the area.
To achieve cleanly hoed soil always ensure that
you guide the machine in straight lines wherever
possible. Insodoing, the aeration swaths should
always overlap each other by a few centimeters in
order to avoid bare strips.
Switch o the motor promptly when you arrive at
Anl_GC-RT_1545_SPK9.indb 18Anl_GC-RT_1545_SPK9.indb 18 07.04.2022 09:55:3007.04.2022 09:55:30
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Einhell GC-RT 1545 M bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Einhell GC-RT 1545 M in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 1,29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info