663877
4
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
IMPORTANT INFORMATION
1. WARNING: EVEN THOUGH ALL SCISSORS MAY APPEAR TO BE SIMILAR, THERE ARE
MAJOR DIFFERENCES AMONG THEM THAT MUST BE UNDERSTOOD BEFORE YOU USE THIS
SHARPENER. THE ScissorPro
®
WILL SHARPEN MOST, BUT NOT ALL TYPES OF SCISSORS.
DO NOT ATTEMPT TO SHARPEN HAIR STYLING SCISSORS, PINKING SHEARS, MANICURE
SCISSORS, SERRATED BLADES, TIN SNIPS, SCISSORS GREATER THAN 12” IN LENGTH OR ANY
BLADE THAT DOES NOT FIT READILY IN THE SHARPENING POSITION.
ScissorPro
®
will sharpen most other blades, including those of knife-edge scissors, as
described later. It is essential that you follow the instructions to optimize your results.
2. Obviously, all scissors have two blades, Not so obvious is that often these blades are very
different. When you cut with scissors, one blade (the anvil blade) is below the material, and the
other blade (the cutter blade) is above the material, as shown in Figure 4. With certain scissors,
the blade on top of the material (the cutter blade) does most of the cutting.
There are several ways to distinguish the cutter and anvil blades. Referring to Figures 3 and
4, note the cutter blade usually has the oblong finger-hold and a more rounded tip. The anvil
blade has a more pointed tip and a round finger hold.
3. It is important to be able to identify the special knife-edge type scissors. They have a cutter
blade factory sharpened at a very low angle to form a knife like edge that is extremely sharp.
THE KNIFE-EDGE BLADE MUST BE SHARPENED ONLY WITH THE KNIFE-EDGE ACCESSORY
SUPPLIED WITH EACH ScissorPro
®
. With these scissors, the knife-edge cutter blade does
virtually all the cutting. When sharpening this type of scissors, only the knife-edge cutter blade
needs to be sharpened. If you have any doubt about whether you have this type of scissors,
ask your nearest fabric or sewing center to help you identify these special blades before you
sharpen them.
4
Figure 5. Carefully feel for a burr along the
entire back of the blade. Note arrow for
direction of finger movement when in contact
with blade.
Figure 4. Typical position of the Cutter Blade
and Anvil Blade.
Cutter Blade
Anvil Blade
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw EdgeCraft ScissorPro 500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van EdgeCraft ScissorPro 500 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info