547014
22
Verklein
Vergroot
Pagina terug
1/23
Pagina verder
22
button has been pressed.
Under normal battery conditions the LED will
extinguish when the button is released.
Motion Sensors
Under low battery conditions the LED behind the
sensor lens will flash when movement is detected to
indicate that the battery needs to be replaced.
Under normal battery conditions the LED does not
illuminate unless the Motion Sensor is in Walk Test
mode.
Door/Window Contact Detectors
Under low battery conditions, when the Detector is
activated the transmit LED will be illuminated for
approximately 1s as the door/window is opened.
Under normal battery conditions the LED will not
illuminate as the Detector is operated, (unless the
Detector is in Test Mode with the tamper switch not
being pressed).
MAINTENANCE
Your Alarm System requires very little maintenance.
However, a few simple tasks will ensure its continued
reliability and operation.
CONTROL PANEL
The new batteries have a typical life of 2 years and
need no maintenance during this period. The
batteries will be damaged if they are not in use for long
periods.
DETECTORS AND REMOTE
CONTROLLER
The Detectors require very little maintenance. The
batteries should be replaced once a year or when a low
battery status is indicated.
IMPORTANT: Should you, for any reason, have to
completely power-down the system (e.g. to move the
system to a new premises) first put the system into Test
mode before removing the Control Panel from the
mounting bracket and disconnecting the power supply.
BATTERIES
Before removing the battery cover on any device to
replace the battery, ensure that the system is put into
Test mode to avoid initiating an Alarm.
The specifications for replacement batteries are as
follows:
Remote
Controllers
1 x 3V CR2032 Lithium Cells
(or equivalent)
Door/Window
Contact
Detectors
3 x 1.5V AAA Size alkaline
battery (or equivalent)
Motion Sensors 3 x 1.5V AA Size alkaline
battery (or equivalent)
At the end of their useful life the batteries should be
disposed of via a suitable Recycling Centre. Do not
dispose of with your normal household waste. DO
NOT BURN.
TROUBLESHOOTING
Forgot password
1. Remove Control Panel from the wall, set
Control Panel in test mode as prerequisite.
2. Remove all power sources from the Control
Panel, such as batteries and DC jack.
3. Move the pin of jumper link to reset position and
reconnect batteries or DC jack.
4. After refitting batteries, the Green statut LED
will turn on for three second indicating the
Control Panel is powered up. When LED turns
off, it implies initial power up is successful. Start
operating the Control Panel.
5. The default password is 1234.
6. Move the pin of jumper link to its original
position.
7.
All of settings will be reset including password,
telephone number and ID codes.
Control Panel not reacting to remote controller
or keypad
Restart learning ID code.
Control Panel not reacting to Motion Sensor(s)
and Door/Window Contact Detector(s)
Restart learning ID code.
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Eden HA700 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Eden HA700 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,95 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Eden HA700

Eden HA700 Gebruiksaanwijzing - Deutsch - 29 pagina's

Eden HA700 Gebruiksaanwijzing - Français - 29 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info