772500
9
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
5,FAQ
5.1. Why is the printing model not adhesive to the printing bed?
1 The nozzle is too far away from the bed, Adjust the distance between the nozzle and the platform, to
assure that the distance is just a sheet of paper
2Hotbed temperature is too high or too low. The temperature of ABS printing hotbed should be
about 110, and that of PLA printing hotbed should be about 50.
5.2. Why the filament do not come out from the nozzle?
1 Check the feeding : check the feeding motor is working normal or not.
2Check the temperature of the sliced file
PLA Filament temperature 180-220, temperature too low may cause this problem
3Check whether the nozzle is blocked
When the temperature of the nozzle is heated(PLA is heated to 210 )and then do feed, pushed
slightly by hand to see if the nozzle is out of filament silk . If the nozzle is out of silk, there is no block
in the nozzle. If no silk come out, remove the nozzle to clean up inside the nozzle or replace the
nozzle.
4 Is the platform too close to the nozzle?
If the platform is too close to the nozzle, there is no space for filament silk come out, you
need adjust the distance between the nozzle and platform, the distance should be right the
thickness of a sheet of paper.
5.3. The problem of print model misplaced
1Slice model error:
The most common software used today is Cura and Repetier. Most of them are open source, so
we can't guarantee the stability and professionalism of the software, and every design model drawing
is not necessarily perfect for the software, so first of all, printing dislocation model diagram is not
changed, slice the model again.
2Model drawings problem:
After slicing, the model is always misplaced. Change another model to print
, or try a model you printed successful before, to check if it is model file problem.
3 The print nozzle is forcibly blocked during printing:
First of all, you can't touch the moving print head with your hand during the printing process.
Secondly, if there are accumulated things on the up layer of the model , the next printing will repeat
the increase of accumulated tumors. A certain degree of hard accumulated tumors will block the
nozzle from moving normally and cause the motor to lose step leading to dislocation.
4Voltage instability:
5motherboard problem
The above problems can not solve the problem, and all models print with same problem , replace
the motherboard.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Easy Threed X6 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Easy Threed X6 in de taal/talen: Engels als bijlage per email.

De handleiding is 2.28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info