542403
17
Verklein
Vergroot
Pagina terug
1/19
Pagina verder
GB GB
18. Changing batteries:
Battery change only in the thermo-hygro-sensor:
1. Open the battery cover
2. Remove the old batteries and insert with new ones of the rec-
ommended type and replace the cover
Once the sensor is powered up, press and hold the PLUS(+) key for
approx. 2 seconds in the normal display mode, the base station will
sound a short beep and synchronize to the sensor otherwise no
weather data will be received.
Battery change only in the base station:
1. Connect power adaptor to base station and power outlet.
2. Open the battery cover located at the back of the base station.
3. Remove the old batteries, insert with new ones of the recom-
mended type and replace the cover
This method of battery replacement will result in no loss of MIN/MAX
and history data. However in case of possible power failure, the base
station will lose the MIX/MAX and all weather data recordings and will
need to be synchronized to the sensors again by pressing the
PLUS(+) key for 2 seconds.
Note:
When batteries require replacement for the base station, the low
battery indicator will light up on the LCD.
Please participate in the preservation of the environment
by properly disposing of all used-up batteries and accu-
mulators at designated disposal points. Never dispose of
batteries in a fire as this may cause explosion, risk of fire
or leakage of dangerous chemicals and fumes
19. Interferences and problems with operation
Problem & cause Remedy
Distance between
transmitters and re-
ceiver too long.
Reduce distance between transmitters
and receiver to receive signal
High shielding materi-
als between the units
(thick walls, steel, con-
crete, isolating alumi-
num foil and etc.)
Find a different location for sensors
and/or receiver. See also Item ‘Trans-
mission Range’ below.
Interference from other
sources (e.g. wireless
radio, headset,
speaker, etc. operating
on the same frequency)
Find a different location for the sensors
and/or base station. Neighbors using
electrical devices operating on the
433MHz signal frequency can also
cause interference with reception
No Reception after
adding extension ca-
bles
Find a new location for the sensors
and/or base station. Recommend not
adding more than 10 meter extension
cables between units to the existing
cable lengths as this will increase the
chance data reception problems.
Reception then no
reception - loss of
transmission signal
from the sensor to the
base station
Press and hold the PLUS(+) key for 2
seconds to synchronize the base sta-
tion to the sensors for weather data
reception. If still no signal, then
change the sensor batteries and syn-
chronize the units again.
Poor contrast LCD or
no reception or low
batteries in sensors or
receiver.
Check the LCD contrast setting or
change batteries (check low battery
indicator on the LCD)
Quite frequently interferences are only of a temporary nature and may
be easily overcome. If there are wireless headsets, remote babysit-
ters or other devices working on 433MHz in your house or in the vicin-
ity, their switch-on time is mostly limited. Furthermore most of these
devices allow the change to an interference-free frequency. Such
measures will effectively overcome interferences.
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw ELV WS2300 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van ELV WS2300 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,47 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info