613277
33
Verklein
Vergroot
Pagina terug
1/34
Pagina verder
13
2 A
1 A
1
2
12.5 Stop motor setting S359 600045 XXX - EFKA DC 1600/DA82GA
12.5.1 Setting position reader
- set the parameter 170, the display will show Sr1 (reference position)
- depress the pushbutton >>, the display will show PoS 0 and the changing rotation symbol
- turn the hand wheel until the rotation symbol disappears
- turn the hand wheel in such a way, so that the needle point ,when moving downward, is on the level of the throat plate
- depress the pushbutton E and pass to the parameter 171
- set the parameter 171, the disply will show Sr2 (all positions)
- depress the pushbutton >>
- the display will show 1 XXX (value of the bottom position)
- turn the hand wheel, until the value XXX begins to change
- turn the hand wheel at the value of the bottom position angle (160 on the panel)
- depress the pushbutton E
- the display will show 2 XXX (value of the top position)
- turn the hand wheel, until the value XXX begins to change
- turn the hand wheel at the value of the top position angle (460 on the panel)
- depress the pushbutton P 2x (return to the sewing mode)
- tread shortly forward the pedal (memory entry)
12.5.2 Changes of setting parameters of stop motor setting considering original producer setting
Parameter Parameter
No value
111 - Max. revolutions (according to a type of machine)
170 - Reference position
171 1 160 Lower position
2 460 Upper position
190 300 Switch on angle of thread trimmer (210
°)
202 120 Delay of start run after switch off the signal foot
210 200 Stopping time for fancy bar
213 5 Time off full power of backtacking
12.6 Stop motor setting S359 600052 XX - EFKA VD 552/6F82FA
12.6.1 Setting position reader
Positions are set by means of discs with cut outs directly in positon reader.
Setting of the lower position:
- dismount the guard of the position reader
- switch on the mains switch
- tread shortly pedal forward (the machine stops in the needle lower position)
- switch off the mains switch
- turn the beginning of the recess 1 of the overlapping disks in such a way, so that the machine stops with the needle in the
position of 3 mm behind the bootom dead center
- check up in repeating the procedure
Setting of the top position of the thread lever:
- tread the pedal rearward (the machine stops in the needle upper position)
- switch off the mains switch
- turn the beginning of the recess 2 in such a way, so that the machine stops with the thread lever in the top dead centre
- check up in repeating the procedure.
33

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Durkopp Adler 528 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Durkopp Adler 528 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Durkopp Adler 528

Durkopp Adler 528 Gebruiksaanwijzing - Deutsch - 34 pagina's

Durkopp Adler 528 Gebruiksaanwijzing - Français - 34 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info