488601
5
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
5
ORIGINAL INSTRUCTIONS
!
ﺮـﻳﺬـﺤـﺗ
READ ALL INSTRUCTIONS.
Failure to follow all instructions
listed below may result in electric shock, fire and/or serious injury.
The term "power tool" in all of the warnings listed below refers to
your mains operated (corded) power tool.
SAVE THESE INSTRUCTIONS
1. WORK AREA
a.  Keep work area clean and well lit. Cluttered and dark areas
invite accidents.
b. Do not operate powertoolsin  explosiveatmospheres, such as 
inthe presenceof flammable liquids,gasesor dust.Power tools
create sparks which may ignite the dust or fumes.
c.  Keep children and bystanders away while operating a power 
tool. Distractions can cause you to lose control.
2. ELECTRICAL SAFETY
a.  Power tool plugs must match the outlet. Never modi fy the 
plug inany way . Do not use any adapterplugs with earthed 
(grounded) power  tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces such 
as pipes, radiators,ranges and refrigerators.There is an
increased risk of electric shock if your body is earthed or
grounded.
c. Do not expose power tools to rainor wet conditions.Water
entering a power tool will increase the risk of electric shock.
d.  Do not abuse the cord. Never use the cord  for ca rrying, 
pulling or unplugging the  powertool. Keep cord away 
from heat, oil,sharpedges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e.  Whenoperating a power tool outdoors, use an ext ension 
cord suitable for outdoor  use. Use of a cord suitable for
outdoor use reduces the risk of electric shock.
3. PERSONAL SAFETY
a. Stayalert,watch what you are doing and use common sense 
when operating a power tool. Do not use a power tool while 
you are tired or under the influence of drugs, alcohol or 
medication.A moment of inattention while operating power
tools may result in serious personal injury.
b. 
Use safety equipment. Always wear eye 
protection.Safety equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal
injuries.
c. Avoid accidental starting.Ensure the switchis in the off 
positionbefore plugging in.Carrying power tools with your
finger on the switch or plugging in power tools that have the
switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power 
tool on. A wrench or a key left attached to a rotating part of
the power tool may result in personal injury.
e. Do not overreach.Keep proper footing and balance at all 
times.This enables better control of the power tool in
unexpected situations.
f. Dress properly.Do  not wear loose clothing or jewellery.Keep 
your hair, clothing and gloves away from moving parts.Loose
clothes, jewellery or long hair can be caught in moving parts.
g. If devicesare provided for the connection of dust extraction 
and collection facilities,ensure these are connectedand 
properlyused.Use of these devices can reduce dust related
hazards.
h.  Do not work materials containing asbestos(asbestos is 
considered carcinogenic).
i.  Take protective measures when during work dust can
develop that is harmful to one's health, combustible or
explosive(some dusts are considered carcinogenic); wear 
a dust mask and work with dust/ chip extracti on when 
connectable.
4. POWER TOOL USE AND CARE
a.  Do not force the power tool. Use thecorrect p ower tool  for 
your application.The correct power tool will do the job better
and safer at the rate for which it was designed.
b.  Do not use thepower tool if the switch does notturn it on 
and off.Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c.  Disconnect the plug from thepower source before making 
any adjustments, changi ng accessor ies,or storing power 
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d.  Store idle powertools outof the reach of children and do 
not allow persons unfamiliar with thepower t ool or these 
instructions to operate thepower tool.
Power tools are dangerous in the hands of untrained users.
e.  Maintain power tools. Check for misalignment or binding of 
moving parts, breakage of parts and an yother condition that 
may affect the power toolsoperation.If damaged, have th e 
power tool r epaired before use. Many accidents are caused
by poorly maintained power tools.
f.  Keep cutting toolssharp andclean.Properly maintained
cutting tools with sharp cutting edges are less likely to bind
and are easier to control.
g.  Use thepower t ool,accessories and tool b its etc., in 
accordance with these instructions and in the manner 
intendedfor the particul ar type of powertool, taking 
into account the working conditions and thework to be 
performed.Use of the power tool for operations different from
intended could result in a hazardous situation.
5. SERVICE
a.  Have your power tool serviced by a qualifiedrepair person 
using only identical replacement parts. This will ensure that
the safety of the power tool is maintained.
GB
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Dremel Engraver 290 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Dremel Engraver 290 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 2,98 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info