32279
3
Verklein
Vergroot
Pagina terug
1/76
Pagina verder
3
Specific Safety Rules
Scroll Station Station
Always disconnect the power cord from the power
source before making any adjustments or attaching any
accessories. Always turn off saw before disconnecting it
to avoid accidental starting when reconnecting to a
power source.
You may unexpectedly cause the tool to start
leading to serious personal injury.
Never leave tool running unattended. Turn power off.
Don't leave tool until it comes to a complete stop.
Never leave the switches in "ON" position. Before plug-
ging the tool in, check that the switches are "OFF".
Accidental start-ups could cause injury.
Do not use tool if switch does not turn it on and off. Have
broken switches replaced by an authorized service center.
Use only Dremel Scroll Station blades. Use the right blade
size, style and cutting speed for the material and the type of
cut. Sharp blades minimize stalling and kickbacks. Blade
teeth should point down toward the table.
Avoid awkward operations and hand positions and
always make sure you have good balance.
A sudden slip
could cause your hand to move into the blade.
Firmly clamp or bolt your saw station to a stable, level
workbench or table.
The most comfortable table height is
approximately waist height.
Never stand on tool. Serious injury could occur if the tool is
tipped or if the blade is unintentionally contacted.
Before making a cut, be sure all adjustments are secure.
Loose table or guards could shift in use and cause you to
loose control of the workpiece.
Always adjust drop foot to just clear the workpiece.
Proper adjustment of the drop foot will help protect your fin
-
gers and keep blade breakage to a minimum.
Always support large workpieces while cutting to mini
-
mize risk of blade pinching and kickback.
Heavy work-
piece may cause the table to slip, walk or slide while cutting.
Be sure the blade path is free of nails. Inspect for and
remove nails from lumber or workpiece before cutting or
sanding.
Keep hands away from cutting area. Do not hand hold
pieces so small that your fingers go under the blade guard.
Do not reach underneath work or in blade cutting path with
your hands and fingers for any reason.
Never start the tool when the blade is in contact with the
workpiece. Allow the motor to come up to full speed
before starting a cut.
Blade in contact with the workpiece
on start up will cause it to jump.
Observe and follow correct direction of feed and do not
feed the material too quickly. Hold the work firmly
against the table.
Feed work into a blade against the teeth
of the blade. Feeding material too forcefully may cause blade
to snap.
Use caution when cutting materials with an irregular
cross-section or rounds like dowel rods. If possible lay
the material on its "flat" side when cutting. For round
stock use a "Vee" block to support the material.
Wavy
material like molding will tend to rock and may bind while cut-
ting. Rounds will tend to roll while being cut and the blade
may "bite" and grab it from your control.
Do not remove jammed cutoff pieces until blade has
stopped. Never touch blade or other moving parts dur-
ing use. Contacting the blade or other moving mechanism
may cause injury.
Power Take Off Safety Rules
The use of attachments and accessories not recom-
mended by Dremel may result in risk of injuries.
Remove the Scroll Station blade and replace it with the
Scroll Station blank in the blade holder before operating
any attachment from the power take off. Avoid the pos-
sibility of contacting the reciprocating blade while sand-
ing.
Inadvertent contact with a blade could cause serious
lacerations.
Unplug the tool before changing accessories or attach-
ments.
Accidental start-ups may occur if sander is plugged
in while changing an accessory.
Keep the cord to the side away from sanding pad or other
attachments.
The cord can be dragged into housing and
become entangled with the pad or other moving components.
Disc Sander Safety Rules
Use only 5" diameter adhesive backed sandpaper discs.
Do not use sandpaper intended for larger sanding pads.
Larger sandpaper will extend beyond the sanding pad caus-
ing snagging, tearing of the paper or kickback.
Make sure the sandpaper disc is not torn or loose before
turning tool on.
The disc could fly away unexpectedly.
Properly adjust sanding disc to avoid it overhanging the
pad.
Spinning sanding disc overhanging its pad can cause
severe lacerations.
Always position your workpiece on the downward side of
the direction of rotation arrow while sanding.
Hold the
work firmly against the table. Sanding on the upward side of
the rotation could cause the workpiece to lift up or kickback.
Refer to rotation arrow on your sander guard.
Avoid awkward hand positions while sanding. A sudden
slip could cause a hand to move into abrasive disc.
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Dremel 1800 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Dremel 1800 in de taal/talen: Engels, Frans, Spaans als bijlage per email.

De handleiding is 1,76 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info