653171
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
What is a cylinder thermostat?
... an explanation for householders
A cylinder thermostat switches on and off the heat
supply from the boiler to the hot-water cylinder. It
works by sensing the temperature of the water inside
the cylinder, switching on the water heating when the
temperature falls below the thermostat setting, and
switching it off once this set temperature has been
reached.
Turning a cylinder thermostat to a higher setting will
not make the water heat up any faster. How quickly the
water heats up depends on the design of the heating
system, for example, the size of boiler and the heat
exchanger inside the cylinder.
The water heating will not work if a time switch or
programmer has switched it off. And the cylinder
thermostat will not always switch the boiler off,
because the boiler sometimes needs to heat the
radiators.
Cylinder thermostats are usually fi tted between one
quarter and one third of the way up the cylinder. The
cylinder thermostat will have a temperature scale
marked on it, and it should be set at between 60C
and 65C, then left to do its job. This temperature is
high enough to kill off harmful bacteria in the water,
but raising the temperature of the stored hot water
any higher will result in wasted energy and increase
the risk of scalding.
If you have a boiler control thermostat, it should
always be set to a higher temperature than that of
the cylinder thermostat. In most boilers, a single
boiler thermostat controls the temperature of water
sent to both the cylinder and radiators, although in
some there are two separate boiler thermostats.
MiStat
TM
C
Cylinder Thermostat
Model: C110C
Customer Service Tel: 0845 130 5522
Customer Service Fax: 0845 130 0622
Technical Helpline: 0845 130 7722
Website: www.draytoncontrols.co.uk
E-mail: customer.care@draytoncontrols.co.uk
l
@DraytonControls
x
/DraytonControls
EU Design Regs:- 002180638-1/2/3
User Guide 06490192001 Iss F
MiTime
MiStat
MiTime
MiStat
HOMEOWNER Guide
HOMEOWNER Guide
Step 5: Receiver - Key & LED
Step 1: Keys and Display - MiStat
RF Pack: MiStat C110C
Step 2: +hr (Timer)
MiStat
Press +hr to start the Timer. The prior used
temperature and time will be displayed and the
temperature will fl ash.
MiStat
Press +/- to adjust +hr temperature, then press ( )
t o c o n r m .
Press +/- to adjust +hr period between 0 and 23 hours.
Press (
) t o c o n r m .
Step 3: Additional User Settings
ID Feature: Description: Factory Pre-Set:
1 MAX-TEMP
It will not be possible to set a higher
temperature
If MAX-TEMP and MIN-TEMP are
set to the same value, it will not be
possible to change temperature
with the +/- keys.
70°C
2 MIN-TEMP
It will not be possible to set a lower
temperature
40°C
DONE
Exit from the settings menu to USER-S
Lamp
colour
Mode Action Key
Function
Green Normal Call for heat
(boiler is fi ring)
None
Green
Flashing
Normal RF
communication
None
Off Normal No call for heat
(boiler is not
fi r i n g )
None
Red RF loss
or not
bound
No call for heat Switches
the boiler
On for 1hr
Amber RF loss
or not
bound
Call for heat Switches the
boiler Off
Battery Handling
Batteries, rechargeable or not, should not be disposed
of into ordinary household waste. Instead, they must be
recycled properly to protect the environment and cut down
the waste of precious resources.
Your local waste management authority can supply details
concerning the proper disposal of batteries.
In compliance with the EU Directive 2006/66/EC, the button
cell battery located on the printed circuit board inside the
product, can be removed at the end of the product life, by
professional personnel only.
Step 4: Changing the Batteries
How do I know when to change
the batteries?
When the batteries start to run low a battery icon will
ash in the display to indicate “low battery”, during
this time the MiStat will function normally. When
the battery icon alone is shown in the display, the
batteries are completely exhausted and the MiStat will
cease to function (see below). Re-activate by replacing
the batteries.
How to replace the batteries
Remove the battery covers as shown. Replace the batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries ensuring
correct orientation. Replace the battery covers pressing fully home.
Battery Covers:
Slide outwards
to remove
MiStat Rear
LED: See table below for details
Key: See table below for details
MiStat
MiStat
MiStat
MiStat
MiStat
MiStat
MiStat
To set a suitable temperature for up to 23 hours, e.g.
for short term absence.
Now the timer is running. The time will be counted
down each hour.
Once the time has elapsed, control returns to the prior
temperature screen.
The Timer can be cancelled by pressing
key or by
setting the +hr period to 0.
Customize the controller according to personal requirements.
To enter User Settings
Press + & – keys for approx. 5
Seconds to enter the settings
menu as shown below.
Press Select (
) to enter the user
settings.
To exit User Settings
Press + & keys for approx. 5
seconds to exit.
If there is no key pressed for
2 minutes the system will exit
the menu, any changes will be
saved.
Troubleshooting:
1 Setting temperature values is restricted
a
Are Minimum/Maximum temperatures activated?
see Homeowner Guide Step 3.
2
NO SIGNAL is visible on the screen, no reaction on
key presses anymore
a
Is the receiver powered? (Red signal lamp should
be visible)
3 LOCKED is displayed
a see Installation Guide Step 5 - LOCK
4 Is the battery symbol visible?
a Replace batteries, see Homeowner Guide Step 4.
5
STARTING is visible on the screen, no reaction on
key presses anymore
a
Is the receiver powered? (Red signal lamp should
be visible)
6
WAIT is visible on the screen, no reaction on key
presses anymore
a
Is the receiver powered? (Red signal lamp should
be visible)
MiStat
Current hot water temperature
Current set temperature
Call for heat indication.
This fl ame will be visible
when the hot water
temperature is below
the set temperature.
+hr key: Press to set a
suitable temperature
for up to 23 hours (see
step 2).
Select key: Press
to open and save
editor screens
+ & - keys:
Press to change
the current
temperature.
key: Press to
cancel +hr and
display home.
RF transmission indication. The
RF symbol will be visible as
follows,
Short fl ashes = RF transmission
Continuous ashing = RF signal
issue
Client Invensys File Name 7449 Instruction Manual Amends 6490192_F V2
Artworker -
Proof Stage
PRINT
Finished Size A3 297x420mm
Creative Director Mike Lane Artwork % 100%
Modification Date 18/06/15 10:26AM Bleed 3mm
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Drayton MiStat C - C110C bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Drayton MiStat C - C110C in de taal/talen: Engels als bijlage per email.

De handleiding is 3,85 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info