680247
216
Verklein
Vergroot
Pagina terug
1/221
Pagina verder
VigorSwitch P2121User’s Guide
206
After the frame is assembled, when transmitting the frame, the preamble (PRE) bytes are
inserted and sent first, then the next, Start of frame Delimiter (SFD), DA, SA and through the
data field and FCS field in turn. The followings summarize what a MAC does before
transmitting a frame.
1. MAC will assemble the frame. First, the preamble and Start-of-Frame delimiter will be
put in the fields of PRE and SFD, followed DA, SA, tag ID if tagged VLAN is applied,
Ethertype or the value of the data length, and payload data field, and finally put the FCS
data in order into the responded fields.
2. Listen if there is any traffic running over the medium. If yes, wait.
3. If the medium is quiet, and no longer senses any carrier, the MAC waits for a period of
time, i.e. inter-frame gap time to have the MAC ready with enough time and then start
transmitting the frame.
4. During the transmission, MAC keeps monitoring the status of the medium. If no collision
happens until the end of the frame, it transmits successfully. If there is a collision
happened, the MAC will send the patterned jamming bit to guarantee the collision event
propagated to all involved network devices, then wait for a random period of time, i.e.
backoff time. When backoff time expires, the MAC goes back to the beginning state and
attempts to transmit again. After a collision happens, MAC increases the transmission
attempts. If the count of the transmission attempt reaches 16 times, the frame in MAC’s
queue will be discarded.
Ethernet MAC transmits frames in half-duplex and full-duplex ways. In halfduplex operation
mode, the MAC can either transmit or receive frame at a moment, but cannot do both jobs at
the same time.
As the transmission of a MAC frame with the half-duplex operation exists only in the same
collision domain, the carrier signal needs to spend time to travel to reach the targeted device.
For two most-distant devices in the same collision domain, when one sends the frame first,
and the second sends the frame, in worstcase, just before the frame from the first device
arrives. The collision happens and will be detected by the second device immediately.
Because of the medium delay, this corrupted signal needs to spend some time to propagate
back to the first device. The maximum time to detect a collision is approximately twice the
signal propagation time between the two most-distant devices. This maximum time is
traded-off by the collision recovery time and the diameter of the LAN.
In the original 802.3 specification, Ethernet operates in half duplex only. Under this condition,
when in 10Mbps LAN, it’s 2500 meters, in 100Mbps LAN, it’s approximately 200 meters and in
1000Mbps, 200 meters. According to the theory, it should be 20 meters. But it’s not practical,
so the LAN diameter is kept by using to increase the minimum frame size with a
variable-length non-data extension bit field which is removed at the receiving MAC. The
following tables are the frame format suitable for 10M, 100M and 1000M Ethernet, and some
parameter values that shall be applied to all of these three types of Ethernet.
Actually, the practice Gigabit Ethernet chips do not feature this so far. They all have their
chips supported full-duplex mode only, as well as all network vendors’ devices. So this
criterion should not exist at the present time and in the future. The switch’s Gigabit module
supports only full-duplex mode.
216

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Draytek VigorSwitch P2121 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Draytek VigorSwitch P2121 in de taal/talen: Engels als bijlage per email.

De handleiding is 4,09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info