680242
208
Verklein
Vergroot
Pagina terug
1/211
Pagina verder
VigorSwitch G2280 User’s Guide
200
A
A
-
-
3
3
F
F
l
l
o
o
w
w
C
C
o
o
n
n
t
t
r
r
o
o
l
l
Flow control is a mechanism to tell the source device stopping sending frame for a specified
period of time designated by target device until the PAUSE time expires. This is accomplished
by sending a PAUSE frame from target device to source device. When the target is not busy
and the PAUSE time is expired, it will send another PAUSE frame with zero time-to-wait to
source device. After the source device receives the PAUSE frame, it will again transmit
frames immediately. PAUSE frame is identical in the form of the MAC frame with a pause-time
value and with a special destination MAC address 01-80-C2-00-00-01. As per the specification,
PAUSE operation can not be used to inhibit the transmission of MAC control frame.
Normally, in 10Mbps and 100Mbps Ethernet, only symmetric flow control is supported.
However, some switches (e.g. 24-Port GbE Web Smart Switch) support not only symmetric but
asymmetric flow controls for the special application. In Gigabit Ethernet, both symmetric
flow control and asymmetric flow control are supported. Asymmetric flow control only allows
transmitting PAUSE frame in one way from one side, the other side is not but
receipt-and-discard the flow control information. Symmetric flow control allows both two
ports to transmit PASUE frames each other simultaneously.
I
I
n
n
t
t
e
e
r
r
-
-
f
f
r
r
a
a
m
m
e
e
G
G
a
a
p
p
t
t
i
i
m
m
e
e
After the end of a transmission, if a network node is ready to transmit data out and if there is
no carrier signal on the medium at that time, the device will wait for a period of time known
as an inter-frame gap time to have the medium clear and stabilized as well as to have the jobs
ready, such as adjusting buffer counter, updating counter and so on, in the receiver site.
Once the inter-frame gap time expires after the de-assertion of carrier sense, the MAC
transmits data. In IEEE802.3 specification, this is 96-bit time or more.
C
C
o
o
l
l
l
l
i
i
s
s
i
i
o
o
n
n
Collision happens only in half-duplex operation. When two or more network nodes transmit
frames at approximately the same time, a collision always occurs and interferes with each
other. This results the carrier signal distorted and undiscriminated. MAC can afford detecting,
through the physical layer, the distortion of the carrier signal. When a collision is detected
during a frame transmission, the transmission will not stop immediately but, instead,
continues transmitting until the rest bits specified by jamSize are completely transmitted.
This guarantees the duration of collision is enough to have all involved devices able to detect
the collision. This is referred to as Jamming. After jamming pattern is sent, MAC stops
transmitting the rest data queued in the buffer and waits for a random period of time, known
as backoff time with the following formula. When backoff time expires, the device goes back
to the state of attempting to transmit frame. The backoff time is determined by the formula
below. When the times of collision is increased, the backoff time is getting long until the
collision times excess 16. If this happens, the frame will be discarded and backoff time will
also be reset.
F
F
r
r
a
a
m
m
e
e
R
R
e
e
c
c
e
e
p
p
t
t
i
i
o
o
n
n
In essence, the frame reception is the same in both operations of half duplex and full duplex,
except that full-duplex operation uses two buffers to transmit and receive the frame
independently. The receiving node always “listens” if there is traffic running over the
medium when it is not receiving a frame. When a frame destined for the target device comes,
208

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Draytek VigorSwitch G2280 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Draytek VigorSwitch G2280 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info