745850
48
Verklein
Vergroot
Pagina terug
1/162
Pagina verder
Remote control with thermostat
Setting display and time
After you insert the battery, or if you press AUTO and
TIMER at the same time, the display will flash. You are in
SET mode.
Press AUTO to switch from °F and 12-hour time to °C
and 24-hour time or vice versa.
Press to set the hours and to set the minutes.
Wait or press TIMER to return to manual mode.
Programming the desired temperature
Press AUTO until the display flashes.
Press or to set the desired temperature.
Wait or press AUTO to switch to automatic mode.
A sensor in the transmitter measures the room tem-
perature. If required, it will send a signal to the receiver to
direct knob B on the gas block and raise or lower the
flames.
Programming the timer
Press TIMER until P1 flashes (period 1, heating cycle
on).
Set the start time of the first heating period by pressing
to set the hours and to set the minutes.
Press TIMER,P1 appears (period 1, heating cycle
off).
Set the end time of the first heating period.
Press TIMER again to set the second heating period
(P2 on and P2 off).
Confirm by pressing TIMER once again.
If only 1 heating period is desired, specify the same
time for P2 and P2 .
Manual mode (MAN on display) - flame height is
adjusted manually
Knob : turn knob B to the left, flow increases,
flames grow larger.
Knob : turn knob B to the right, flow decreases,
flames become smaller.
The “send” symbol appears in the top left corner of the dis-
play every time you press one of the buttons. The light on
the receiver starts flashing when knob B reaches the end
stop.
Automatic mode (AUTO on display) - flame height is
adjusted thermostatically
Briefly press AUTO. The set temperature appears briefly
on the display, followed by the room temperature.
Timer mode (TIMER on display)
During the specified heating periods (P1 and P2 ), the
appliance works as it does in AUTO mode.
When the program switches to (heating cycle off), the
main burner goes out and only the pilot flame continues to
burn. There are no further temperature checks; this saves
the battery.
Check the temperature set by pressing AUTO and then
TIMER.
You can make manual adjustments by pressing the but-
tons and .
To save battery life, set the handset to MAN mode
before switching the stove off, and press until the end
stop of knob B has been reached. If the handset stays in
AUTO or TIMER mode, the handset will continue to use
the battery even if the appliance is off.
Replacing the battery
If BATT appears in the top right corner of the display, or if
the lamp on the receiver becomes dimmer, the respective
18 Subject to change because of technical improvements
48

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Dovre ASTRO4GAP bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Dovre ASTRO4GAP in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 11,34 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info