599928
16
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
16
these operations have been performed regularly and
properly.
Only maintenance work described in this instruction
manual may be performed by the user. Any other work
must be carried out by DOLMAR authorized service
centers.
Cleaning the chain saw
Clean the saw regularly with a clean rag. The handles, in
particular, must be kept free of oil.
Checking the plastic housing
Carry out regular visual inspections of all parts of the
housing. If any parts are damaged, have them repaired
immediately and properly in DOLMAR authorized service
centers.
Sharpening the saw chain
CAUTION:
Always withdraw the mains plug and wear safety
gloves when performing work on the saw chain.
Sharpen the saw chain when: (Fig. 35)
Mealy sawdust is produced when damp wood is cut;
The chain penetrates the wood with difficulty, even
when heavy pressure is applied;
The cutting edge is obviously damaged;
The saw pulls to the left or right in the wood. The
reason for this behavior is uneven sharpening of the
saw chain, or damage to one side only.
Sharpen the saw chain frequently, but remove only a
little material each time.
Two or three strokes with a file are usually sufficient for
routine resharpening. When the saw chain has been
resharpened several times, have it sharpened in
DOLMAR authorized service center.
Sharpening criteria:
All cutter length must be equal. Cutters of differing
length prevent the chain from running smoothly, and
may cause the chain to break.
Do not sharpen the chain once a minimum cutter length
of 3 mm has been reached. A new chain must then be
fitted.
The chip thickness is determined by the distance
between the depth gauge (round nose) and the cutting
edge.
The best cutting results are obtained with following
distance between cutting edge and depth gauge.
Chain blade 492 (91PX): 0.65 mm (Fig. 36)
WARNING:
An excessive distance increases the risk of kick-back.
The sharpening angle of 30° must be the same on all
cutters. Differences in angle cause the chain to run
roughly and unevenly, accelerate wear, and lead to
chain breaks.
The side plate angle of the cutter is determined by the
depth of penetration of the round file. If the specified
file is used properly, the correct side plate angle is
produced automatically.
Side plate angle for each saw chain are as follows:
Chain blade 492 (91PX): 80° (Fig. 37)
File and file guiding
Use a special round file (optional accessory) for saw
chains to sharpen the chain. Normal round files are not
suitable.
Diameter of the round file for each saw chain is as
follows:
Chain blade 492 (91PX): 4.0 mm
The file should only engage the cutter on the forward
stroke. Lift the file off the cutter on the return stroke.
Sharpen the shortest cutter first. Then the length of this
shortest cutter becomes the standard for all other
cutters on the saw chain.
Guide the file as shown in the figure. (Fig. 38)
The file can be guided more easily if a file holder
(optional accessory) is employed. The file holder has
markings for the correct sharpening angle of 30° (align
the markings parallel to the saw chain) and limits the
depth of penetration (to 4/5 of the file diameter).
(Fig. 39)
After sharpening the chain, check the height of the
depth gauge using the chain gauge tool (optional
accessory). (Fig. 40)
Remove any projecting material, however small, with a
special flat file (optional accessory).
Round off the front of the depth gauge again.
Cleaning the guide bar and lubricating the
return sprocket
CAUTION:
Always wear safety gloves for this task. Burrs present a
risk of injury.
Check the running surfaces of the bar regularly for
damage. Clean using a suitable tool, and remove burrs if
necessary. (Fig. 41)
If the chain saw receives frequent use, lubricate the return
sprocket bearing at least once a week. Before adding new
fresh grease, carefully clean the 2 mm hole on the tip of
the guide bar, then force a small quantity of multi-purpose
grease (optional accessory) into the hole.
Cleaning the oil guide (Fig. 42)
Clean the oil guide groove and the oil feed hole in the
bar at regular intervals.
New saw chains
Use two or three saw chains alternately, so that the saw
chain, sprocket and running surfaces of the bar wear
evenly.
Turn the bar over when changing the chain so that the bar
groove wears evenly.
CAUTION:
Only use chains and bars which are approved for this
model of saw (refer to “SPECIFICATIONS”).
Before fitting a new saw chain, check the condition of the
sprocket. (Fig. 43)
CAUTION:
A worn sprocket damages a new saw chain. Have the
sprocket replaced in this case.
Always fit a new locking ring when replacing the sprocket.
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Dolmar ES-2146 TLC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Dolmar ES-2146 TLC in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens als bijlage per email.

De handleiding is 2,65 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Dolmar ES-2146 TLC

Dolmar ES-2146 TLC Gebruiksaanwijzing - Nederlands - 20 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info