599928
13
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
13
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to safety
rules for the subject product. MISUSE or failure to
follow the safety rules stated in this instruction
manual may cause serious personal injury.
DESIGNATION OF PARTS
(Nut model: the sprocket cover is tightened by nuts.)
For Model ES-154, ES-164, ES-174, ES-184, ES-2131,
ES-2136, ES-2141, ES-2146 (Fig. 5)
(Lever model: the sprocket cover is tightened by lever.)
For Model ES-154 TLC, ES-164 TLC, ES-174 TLC,
ES-184 TLC, ES-2131 TLC, ES-2136 TLC,
ES-2141 TLC, ES-2146 TLC (Fig. 6)
(For all models) (Fig. 7)
ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Removing or installing sprocket cover
To remove the sprocket cover, perform the following
steps:
(For nut models) (Fig. 8)
Loosen the nut.
(For lever models) (Fig. 9)
Press and fully open the lever until it stops.
Turn the lever counterclockwise.
To install the sprocket cover, perform the above steps in
reverse.
Removing or installing saw chain
CAUTION:
Always wear gloves when installing or removing the
saw chain.
To remove the saw chain, perform the following steps:
1. Loosen the sprocket cover.
2. (For nut models) Turn the chain adjusting screw
counterclockwise to release the saw chain tension.
(For lever models) Turn the adjusting dial to “-”
direction to loosen the saw chain tension. (Fig. 10 &
11)
3. Remove the sprocket cover.
4. Remove the saw chain and guide bar from the chain
saw.
To install the saw chain, perform the following steps:
5. Make sure the direction of the chain. The arrow mark
on the chain shows the direction of the chain. (Fig. 12)
6. Fit in one end of the saw chain on the top of the guide
bar and the other end of it around the sprocket.
7. Place the guide bar on the chain saw.
8. Align the tension slide with the hole of the guide bar.
(Fig. 13)
9. Holding the guide bar, and turn the chain adjusting
screw/dial to adjust the saw chain tension.
10. Place the sprocket cover so that the hooks fit
alongside the holes and the pin fits its counterpart on
the sprocket cover. (Fig. 14)
11. Tighten the sprocket cover. (Fig. 15 & 16)
Adjusting saw chain tension
The saw chain may become loose after many hours of
use. From time to time check the saw chain tension
before use.
1. Loosen the sprocket cover lightly.
2. Lift up the guide bar tip slightly.
3. Turn the adjusting screw/dial to adjust saw chain
tension. (Fig. 17 & 18)
4. Tighten the saw chain until the lower side of the saw
chain fits in the guide bar rail (see circle).
5. Keep holding the guide bar lightly, tighten the sprocket
cover after adjusting the chain tension. Make sure that
the saw chain does not loose at lower side.
Make sure the saw chain fits snugly against the lower side
of the bar.
CAUTION:
Do not tighten the saw chain too much. Excessively
high tension of saw chain may cause breakage of saw
chain, wear of the guide bar and breakage of the
adjusting dial.
A chain which is too loose can jump off the bar, and
therefore presents an accident risk.
Carry out the procedure of installing or removing saw
chain in a clean place free from sawdust and the like.
Engaging extension cord
CAUTION:
Make sure that the extension cord is unplugged to the
mains outlet. (Fig. 19)
When engaging the extension cord, secure it to the chain
saw’s cord with the cord hook.
Attach the cord hook about 100 - 200 mm from the
extension cord connector. This helps prevent
unintentional disconnection.
OPERATION
CAUTION:
Hold the tool firmly with right hand on the rear handle
and left hand on the front handle when performing the
tool.
Switch action (Fig. 20)
CAUTION:
Always be sure that the tool is switched off and
unplugged before checking function on the switch
trigger.
Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
“OFF” position when released.
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided.
To start the tool, depress the lock-off button and pull the
switch trigger. Release the switch trigger to stop.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Dolmar ES-2146 TLC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Dolmar ES-2146 TLC in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens als bijlage per email.

De handleiding is 2,65 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Dolmar ES-2146 TLC

Dolmar ES-2146 TLC Gebruiksaanwijzing - Nederlands - 20 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info