798035
6
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
ELECTRONIC CLIMATE CONTROL
see Fig. 4
(CDE2ECC & CDE3ECC models only)
Operation
The electronic control allows MANUAL and AUTO
operation.
In MANUAL ON mode there are three heat settings:
L/H Side Heat, R/H Side Heat and High Heat
In AUTO mode the heater comes on as per the programmed
timer settings (see Setting programs). At any point if the
heater is active i.e. heat is being produced, the neon is
lit - see Fig. 4.
Initial Operation
When the heater is connected to the mains the neon will
be lit and the display is blank. Press the button and the
display goes to full heat set to 35oC - see Fig. 8.
Note: All display characters are displayed in Fig. 13.
Standby Mode
With the heater ON if the button is pressed, the heater
will go into standby mode, heater switches off, the display
goes blank and only the MAINS ON neon ( ) remains lit.
On pressing the button again the heater will come on
in the mode and with the settings it had prior to going into
standby mode.
Setting Current Time
1. Press and hold ‘ and the clock symbol ‘ ’ appears
on the top left hand side of the screen. The user can
now set the time.
2. The hour digit will now ash. To adjust the hour use the
& buttons. Conrm the hour digit by pressing
’.
3. The minute digit will ash. To adjust the minute use the
& buttons. Conrm the hour digit by pressing
’. The display will return to the state before
entering set time.
N.B. If no keys are pressed after 4 minutes the display will
revert to the state prior to entering set time.
Manual Operation
Pressing from the default HIGH screen (Fig. 8) brings
the heater into AUTO mode - see ‘Setting the Timer
Programs’. Press again to put the heater into OFF mode -
see Fig. 6. Press again for left hand side heat ( appears
on LCD display - see Fig. 7). Press again for right hand
side heat ( appears on LCD display). Press again brings
the user full circle to FULL heat mode ( appears
on LCD display).
Setting the Desired Temperature
The desired temperature can be set using the ‘ ’ or ‘
keys. The temperature can be set from 5oC to 35oC and
this will be shown on the display. When the temperature
is reached the heater will automatically switch OFF. If the
ambient temperature drops the heater will come on again
automatically. Note the electronic climate control device
conserves energy and assists with temperature regulation
e.g. if the heater is set to HIGH heat and the temperature
is set to 28oC, at 27oC the heater will switch to a lower heat
setting. Then at 28oC the heater will switch off completely.
Setting the Timer Programs
Two program settings are possible, P1 and P2. Only high
heat is possible for program settings. Press ‘ once to set
the programs, starting with P1 AUTO ON – See Fig 10.
1. The hour digit will now ash. To adjust the hour use the
& buttons. Conrm the hour digit by pressing
’.
2. The minute digit will now ash. To adjust the minute
use the ‘ & buttons. Conrm the hour digit by
pressing ‘ ’.
3. Now P1 AUTO OFF is displayed, P1 off time can now
be set. Repeat steps 1 & 2 to set P1 off time.
At this point either:
(a) Press to exit the Program mode and return
to AUTO mode. The heater is now in AUTO mode.
The heater will switch ON and OFF depending on
programme P1 previously entered.
OR
(b) Repeat steps 1 - 3 as above to set the programme
for P2.
At this point press ENTER or PROG to exit the Programme
mode. The heater is now in AUTO mode. The heater will
switch ON and OFF depending on programme P1 & P2
previously entered. If after programming and returning to
the AUTO mode display, P1 or P2 is active, the display will
show PROG 1 AUTO ON or PROG 2 AUTO ON depending
on which is active - see Fig. 11. An OFF time cannot be
entered which is less than the corresponding ON time.
When setting the timer programs if no keys are pressed, the
display will (after 4 minutes) revert to the previous display
i.e. display prior to entering Program mode.
Run Programs
If MODE is pressed until AUTO appears on the screen
(either AUTO-ON or AUTO-OFF), the heater will run both
P1 and P2 program as they are set.
NOTE: The heater cannot be programmed to run P1
only or P2 only.
To cancel P1, set P1 OFF time to be same as P1 ON time.
To cancel P2 set P2 OFF time to be same as P2 ON time.
Review Program settings
To review the program settings the heater must be in AUTO
mode. Press ENTER and the times for PROG 1 ON, PROG
1 OFF, PROG 2 ON and PROG 2 OFF will be displayed
consecutively for 2 seconds. The display will automatically
return to the state it was in before ENTER was pressed.
FROST Protection Mode
With the heater in any mode, OFF, MANUAL ON or AUTO,
if the displayed set temperature is reduced to 5oC the heater
will go into FROST Protection mode - see Fig. 12. In this
mode only, if the ambient temperature drops below 5oC, will
the heater come on. This is to prevent freezing. In FROST
Protection mode the heater comes on in the high heat mode
only. Pressing the button is the only way to bring the
heater out of this special mode.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Dimplex Cadiz Eco CDE3ECC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Dimplex Cadiz Eco CDE3ECC in de taal/talen: Engels als bijlage per email.

De handleiding is 1.52 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info