Handleiding DeWalt DW079 (pagina 48 van 120) (Duits, Engels, Frans, Deens, Zweeds, Noors, Fins)

790947

Verklein

Vergroot

Pagina terug

1/120

Pagina verder

ENGLISH

5. The laser can be adjusted up and down to the

desired offset height for working. To change the

height, loosen the locking knob (hh) located on

the left of the wall mount.

6. Turn the adjustment knob (ii), located to the

right of the wall mount, to move the laser level

up and down to set your height. Use the wall

mount measuring scale (dd) to pinpoint your

mark.

NOTE: It may be helpful to turn the power on

and turn the rotary head so that it puts a dot

on one of the laser scales. The DEWALT target

card is marked at 38 mm (1-1/2"), therefore, it

may be easiest to set the offset of the laser to

38 mm (1-1/2") below the track.

7. Once you have positioned the laser at the

desired height, tighten the locking knob (hh) to

maintain this position.

TRIPOD SET-UP (FIG. 4)

1. Position the tripod securely and set it to the

desired height.

2. Make sure that the top of the tripod is roughly

level. The laser will self-level only if the top of the

tripod is within ± 5˚ of level. If the laser is set up

too far out of level, it will beep when it reaches

the limit of its leveling range. No damage will be

done to the laser, but it will not operate in an

“out of level” condition.

3. Secure the laser to the tripod by screwing the

threaded knob (jj) on the tripod into the female

thread (kk) on the bottom of the laser.

NOTE: Be sure that the tripod you are working

with has a 5/8"–11 threaded screw to ensure

secure mounting.

4. Turn the laser on and adjust the rotation speed

and controls as desired.

FLOOR SET-UP (FIG. 5, 6)

The laser level can be positioned directly on the

floor for leveling and plumbing applications such as

framing walls.

1. Place the laser on a relatively smooth and level

surface where it will not be disturbed.

2. Position the laser for a level (fig. 6A) or plumb

(fig. 6B) setting.

3. Turn the laser on and adjust the rotation speed

and controls as desired.

NOTE: The laser will be easier to set up for wall

applications if the rotation speed is set to 0 rpms

and if the remote control is used to line up the laser

with control marks. The remote allows one person to

set up the laser.

OPERATION

WARNING: Always observe the safety

instructions and applicable regulations.

• To extend battery life per charge, turn the laser

off when it is not in use.

• To ensure the accuracy of your work, check

the laser calibration often. Refer to Field

Callibration Check under Laser Maintenance.

• Before attempting to use the laser, make sure

the tool is positioned on a relatively smooth,

secure surface.

• Always mark the centre of the laser line or

dot. If you mark different parts of the beam at

different times you will introduce error into your

measurements.

• To increase working distance and accuracy, set

up the laser in the middle of your working area.

• When attaching to a tripod or wall, mount the

laser securely.

• When working indoors, a slow rotary head

speed will produce a visibly brighter line; a faster

rotary head speed will produce a visibly solid

line.

• To increase beam visibility, wear Laser

Enhancement Glass es and/or use a Laser

Target Card to help find the beam.

• Extreme temperature changes can cause

movement or shifting of building structures,

metal tripods, equipment, etc., which can affect

accuracy. Check your accuracy often while

working.

• When working with the DEWALT Digital Laser

Detector, set the laser’s rotation speed to the

fastest setting.

• If the laser is dropped or suffers a sharp blow,

have the calibration system checked by a

qualified service centre before using the laser.

Laser Control Panel (ﬁ g. 1)

The laser is controlled by the power button (e), the

speed/rotation button (f), the scan mode button

(g), and two arrows (h, i). The arrows control the

movement of the laser head left and right when the

laser is being used in the plumb mode.

Four LED indicator lights are on the control panel:

power (j), X-axis leveling (k), Y-axis leveling (l) and

remote control private mode (m).

TURNING THE LASER ON (FIG. 1)

1. Insert the fully charged battery pack. Be sure

that the battery door is securely latched.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

DeWalt DW079 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Andere handleiding(en) van DeWalt DW079

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info