790832
19
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
17
ENGLISH
Clamp: DE7082
(similar model
included)
Used for firmly clamping
workpiece to the saw table
for precision cutting.
Dust Bag: DE7053
(included with some
models)
Equipped with a zipper for
easy emptying, the dust bag
will capture the majority of
the sawdust produced.
SAW BLADES: ALWAYS USE 305 mm SAW BLADES WITH 25.4 mm/30 mm ARBOUR HOLES.
SPEED RATING MUST BE AT LEAST 4800 RPM. Never use a smaller diameter blade. It will
not be guarded properly. Use crosscut blades only! Do not use blades designed for ripping,
combination blades or blades with hook angles in excess of 7°.
BLADE DESCRIPTIONS
APPLICATION DIAMETER TEETH
Construction Saw Blades (thin kerf with anti-stick rim)
General Purpose 305 mm 40
Fine Crosscuts 305 mm 60
Woodworking Saw Blades (provide smooth, clean cuts)
Fine crosscuts 305 mm 80
Non-ferrous metals 305 mm 96
Consult your dealer for further information on the appropriateaccessories.
Protecting the Environment
Separate collection. Products and batteries marked with this symbol must not be
disposed of with normal householdwaste.
Products and batteries contain materials that can be recovered or recycled reducing
the demand for raw materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails to produce sufficient power on jobs
which were easily done before. At the end of its technical life, discard it with due care for our
environment:
Run the battery pack down completely, then remove it from thetool.
Li-Ion cells are recyclable. Take them to your dealer or a local recycling station. The
collected battery packs will be recycled or disposed ofproperly.
After several cuts are made at various mitre angles other than 0°, the platform may weaken
and not properly support the work. Install a new, unused platform to the saw after presetting
the desired mitreangle.
CAUTION: Continued use of a platform with several kerfs may cause loss of material
control and possibleinjury.
MAINTENANCE
WARNING: To reduce the risk of serious personal injury, turn tool off and remove
the battery packs or power supply before transporting, making any adjustments,
cleaning, repairing, or removing/installing attachments or accessories. An
accidental start-up can causeinjury.
WARNING: To reduce the risk of serious personal injury, DO NOT touch the sharp
points on the blade with fingers or hands while performing anymaintenance.
DO NOT use lubricants or cleaners (particularly spray or aerosol) in the vicinity of the plastic
guard. The polycarbonate material used in the guard is subject to attack by certainchemicals.
Lubrication
Your power tool requires no additionallubrication.
Cleaning
Before use, carefully check the upper guard, lower guard and dust duct to determine that they
will operate properly. Ensure that chips, dust or workpiece particles do not block of one of
thefunctions.
In case of workpiece fragments jammed between the saw blade and guards, disconnect the
machine from the power supply and follow the instructions given in Changing or Installing a
New Saw Blade. Remove the jammed parts and reassemble the sawblade.
Periodically clean all dust and wood chips from around AND UNDER the base and the
rotarytable.
WARNING: Blow dirt and dust out of the main housing with dry air as often as dirt is seen
collecting in and around the air vents. Wear approved eye protection and approved dust
mask when performing thisprocedure.
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic
parts of the tool. These chemicals may weaken the materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any liquid get inside the tool;
never immerse any part of the tool into aliquid.
Cleaning the
DeWALT
Corded Power Supply
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic
parts of the tool. These chemicals may weaken the plastic materials used in these parts.
Use a cloth dampened only with water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into aliquid.
Cleaning the Corded Power Supply Receptacle (Fig. D)
WARNING: Blow debris out of the corded power supply receptacle37 with clean, dry air.
To minimize the risk of eye injury, always wear eye protection and respiratory protection
when performingthis.
Dust Duct Cleaning
Depending on your cutting environment, saw dust can clog the dust duct and may prevent
dust from flowing away from the cutting area properly. With the battery pack or corded power
supply removed and the saw head raised fully, low pressure air or a large diameter dowel rod
can be used to clear the dust out of the dustduct.
XPS™ LED Worklight Cleaning
For the best worklight performance, perform the following maintenance regularly with the
battery or corded power supplyremoved.
Carefully clean saw dust and debris from worklight lens with a cottonswab.
DO NOT use solvents of any kind, they may damage thelens.
Dust build-up can block the worklight and prevent it from accurately indicating the line
ofcut.
Follow mitre saw’s instruction manual to remove and installblade.
With blade removed from saw, clean pitch and build-up from blade. Pitch and debris can
interfere with the worklight and prevent it from accurately indicating the line ofcut.
Optional Accessories
WARNING: Since accessories, other than those offered by
DeWALT
, have not been tested
with this product, use of such accessories with this tool could be hazardous. To reduce the
risk of injury, only
DeWALT
recommended accessories should be used with thisproduct.
The following accessories, designed for your saw, may be helpful. In some cases, other locally
obtained work supports, length stops, clamps, etc., may be more appropriate. Use care in
selecting and usingaccessories.
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DHS780 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DHS780 in de taal/talen: Engels als bijlage per email.

De handleiding is 6.68 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van DeWalt DHS780

DeWalt DHS780 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanõl, Türkiye, Dansk, Svenska, Norsk, Suomi - 168 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info