723573
39
Verklein
Vergroot
Pagina terug
1/172
Pagina verder
37
ENGLISH
settings that do not overload the tap by driving it too far
beforereversing.
WARNING: Use caution not to drive a tap past the end of
its threads, or to bottom a tap in a blindhole.
WARNING: Always follow tap manufacturer’s guidelines
for proper tap selection and use with different materials,
cutting fluids, tap drill sizes and feedrates.
WARNING: Tapping mode is not recommended for
use with taps less than 8 mm or more than 20mm
indiameter.
WARNING: Recommended tapping speeds in Tables 2
and 3 are a suggestion only, based on test results tapping
new threads at 75% thread depth. It is recommended to
perform a test application on scrap material, starting at
speed 1 and working up. Tapping mode should be used in
the lowest speed that results in an appropriate feed rate
and chip clearing for thematerial.
WARNING: When using advanced tapping mode, always
start with the default forward time and reverse time
shown in Table 4, then increase or decrease asnecessary.
When the Precision Tap™ is enabled, the tool will operate in
forward and then automatically operate in reverse without
releasing the trigger. The tool will continue to alternate
between forward and reverse until the trigger isreleased.
DeWALT
Tool Connect™ (Fig. A)
WARNING: To reduce the risk of injury, remove accessories
from the tool anvil before any Tool Connect™interaction.
NOTICE: Always check the tool configuration prior to
use. If you are unsure of the current configuration, press
the mode selector button 9 (Fig. A) to set the tool to the
Home setting as described on the label and thismanual.
This tool is capable of connecting with mobile devices that
support Bluetooth® Smart (or Bluetooth® 4.0) technology.
(To see if your mobile device is compatible, visit: http://www.
bluetooth.com/Pages/Bluetooth-Smart-Devices-List.aspx)
DeWALT
Tool Connect™ is an optional application for your
smart device (such as a smart phone or tablet) that connects
the device to your tool to allow you to configure specific tool
functions. Refer to Tool ConnectTM ModeSelector.
NOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use of
such marks by
DeWALT
is under license. Other trademarks and
trade names are those of their respectiveowners.
NOTE: The Tool Connect™ App is governed by separate
terms and conditions available for viewing through the
mobileapplication.
Download the
DeWALT
Tool Connect™ applicationat:
Install a fully charged 18V battery pack into the tool. Refer to
Inserting and Removing the Battery Pack from theTool.
Follow the instructions in the app to create your Tool
Connect™account.
On the Home screen of the app, select "+ Tool" to begin the
process of adding your tool to theapp.
To connect your tool with the
DeWALT
Tool Connect™ app,
at the appropriate screen, press the mode selector button9
for 3–5 seconds, then wait for the tool to connect. The tool
can only be connected to one Tool Connect™ account at
atime.
Once the tool has been connected, you can confirm that
you would like to register theproduct.
Coin Cell Battery
Bluetooth® capability is powered by one coin cell battery in
your tool, that when necessary, should be replaced by your local
DeWALT
service centre. Do not attempt to replace the coin cell
batteryyourself.
WARNING: Danger of explosion if battery is
incorrectlyreplaced.
WARNING: DO NOT INGEST BATTERY; CHEMICAL
BURN HAZARD. This product contains a coin/button cell
battery. If the coin/button cell battery is swallowed, it can
cause severe internal burns in just 2hours and can lead
todeath.
Keep new and used batteries away from children. If
the battery compartment does not close securely, stop
using the product and keep it away fromchildren.
If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate
medicalattention.
If the coin cell battery contents come into contact
with the skin, immediately wash area with mild soap
and water. If coin cell battery liquid gets into the eye,
rinse water over the open eye for 15 minutes or until
irritation ceases. If medical attention is needed, the
battery electrolyte is composed of an organic solvent
and lithiumsalts.
Do not incinerate or dispose of tool together with
household waste material! Tool that has reached
the end of its life must be collected separately
and returned to an environmentally compatible
recyclingfacility.
Anvils (Fig. D, E)
WARNING: Use only impact-rated accessories. Non-
impact accessories may break and cause a hazardous
condition. Inspect accessories prior to use to ensure that it
con tains nocracks.
CAUTION: Inspect anvils, detent pins and hog rings prior
to use. Missing or damaged items should be replaced
beforeuse.
Place the switch in the locked off (centre) position or remove
battery pack before changingaccessories.
Anvil with Detent Pin (Fig. D)
DCF896
To install an accessory on the anvil, align the hole in the
side of the accessory with the detent pin 16 on the anvil 3.
Press the accessory on until the detent pin engages in the hole.
Depression of detent pin may be necessary to aid installation
ofaccessory.
39

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DCF896 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DCF896 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 15,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info