549695
12
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
10
NOTE: The worklights are for lighting the immediate work surface and are not
intended to be used as a flashlight.
Quick-Release Bit Holder (Fig. 2, 4, 5)
DCF815-XE
NOTE: The bit holder accepts 6.35 mm (1/4") hex accessories.
Place the forward/reverse button (B) in the locked off (centre) position or remove
battery pack before changing accessories.
FIG. 4
C
D
FIG. 5
C
D
To install an accessory, fully insert the accessory. The accessory is locked into place
(Fig. 4).
To remove an accessory, pull the collar (C) away from the front of the tool. Remove
the accessory and release the collar (Fig. 5).
Anvil with Hog Ring (Fig. 2, 6)
DCF813-XE
WARNING: Use only impact accessories. Non-impact
J
K
FIG. 6
accessories may break and cause a hazardous condition.
Inspect accessory prior to use to ensure that it con tains no
cracks.
CAUTION: Inspect anvils and hog rings prior to use. Missing
or damaged items should be replaced before use.
Place the forward/reverse button (B) in the locked off (centre)
position or remove battery pack before changing accessories.
To install an accessory on the hog ring anvil, firmly push accessory onto the
anvil (J). The hog ring (K) compresses to allow the accessory to slide on. After
the accessory is installed, the hog ring applies pressure to help provide accessory
retention.
To remove a accessory, grasp the accessory and firmly pull it off.
Usage
Your impact tool generates the following output torque:
Cat # Ft.-Lbs. In.-Lbs. Nm
DCF813-XE 96 1150 130
DCF815-XE 79 950 107
CAUTION: Ensure fastener and/or system will withstand the level of torque
generated by the tool. Excessive torque may cause breakage and possible personal
injury.
1. Place the accessory on the fastener head. Keep the tool pointed straight at the
fastener.
2. Press switch to start operation. Always check torque with a torque wrench, as
the fastening torque is affected by many factors including the following:
Voltage: Low voltage, due to a nearly discharged battery, will reduce fastening
torque.
Accessory size: Failure to use the correct accessory size will cause a reduction
in fastening torque.
Bolt Size: Larger bolt diameters generally require higher fastening torque.
Fastening torque will also vary according to length, grade, and torque
coefficient.
Bolt: Ensure that all threads are free of rust and other debris to allow proper
fastening torque.
Material: The type of material and surface finish of the material will affect
fastening torque.
Fastening Time: Longer fasten ing time results in increased fastening torque.
Using a longer fastening time than recom mended could cause the fasteners to
be overstressed, stripped or damaged.
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DCF813 T 3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DCF813 T 3 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van DeWalt DCF813 T 3

DeWalt DCF813 T 3 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanõl, Polski, Türkiye, Dansk, Svenska, Norsk, Suomi - 172 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info