447012
42
Verklein
Vergroot
Pagina terug
1/184
Pagina verder
ENGLISH
40
WARNING: The headlights are intended
for lighting the immediate work surface.
Do not use the headlights as the only
light source.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
Proper Hand Position (fi g. 8)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the main
handle (u) as shown.
Preparing the Tool (fi g. 1, 4)
1. Remove the battery pack (m).
2. Remove all nails from the magazine (g).
3. Release the contact trip lock-off (l).
4. Check if the contact trip can move freely.
5. Engage contact trip lock-off.
6. Reload the nails to the magazine.
7. Insert battery pack.
WARNING: Do not use the tool if the
contact trip or nail pusher cannot move
freely.
NOTICE: NEVER
spray or in any other
way apply lubricants or
cleaning solvents inside
the tool. This can
seriously affect the life
and performance of the tool.
Actuating the Tool (fi g. 1)
The tool can be operated using one of two modes:
sequential action mode or bump action mode.
SEQUENTIAL ACTION MODE
The sequential action mode is used for intermittent
nailing when very careful and accurate placement is
desired.
1. Using the mode selector switch (j), select the
sequential action mode.
2. Release the contact trip lock-off (l).
3. Push the contact trip against the work surface.
4. Pull the trigger switch (a) to actuate the tool.
Each trigger pull with the contact trip pushed
against the work surface will drive one nail.
BUMP ACTION
The bump action mode is used for rapid nailing on
flat, stationary surfaces.
1. Release the contact trip lock-off (l).
2. Using the mode selector switch (j) to select the
bump action mode.
3. To drive a single nail, operate the tool as
described for sequential action:
a. Push the contact trip (b) against the work
surface.
b. Pull the trigger switch (a) to actuate the tool.
Each trigger pull with the contact trip pushed
against the work surface will drive one nail.
4. To drive several nails, depress and hold the
trigger switch (a), and then push the contact trip
(b) repeatedly against the work surface.
WARNING: Do not keep the trigger
depressed when the tool is not in use.
Keep the contact trip (l) lock-off in the
locked position to prevent accidental
actuation when the tool is not in use.
Clearing a Jammed Nail (fi g. 1)
If a nail becomes jammed in the nosepiece, the
headlights (e) will blink continuously.
1. Remove the battery pack (m).
2. Engage the contact trip lock-off (l).
3. Open magazine cover (g).
4. Remove all nails from the magazine.
5. Release the jam clearing latch (c) on top of the
nosepiece.
6. Retract the cover (d) so the jammed nail is
exposed.
7. Remove the nail, using pliers if necessary.
8. If the driver blade is in the down position, insert
a screwdriver into the nosepiece and push the
blade back in position.
42

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DC608 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DC608 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 20,42 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info